Bedienungsanleitung M-System MU-70 (Seite 2 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

522893

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH

DESCRIPTION

The hood may be installed in the filtering or the ducting version. Filtering version (Fig. 1): The hood aspirates

the kitchen air saturated with fumes and odours, purifies it through the grease filters and charcoal filters and returns

clean air into the room. For constant efficiency, the charcoal filters must be replaced periodically. The charcoal

filters are not supplied. Ducting version (Fig. 2): The hood aspirates the kitchen air saturated with fumes and

odours, passes it through the grease filters and expels it to the outside through an outlet pipe. With this version

the charcoal filters are not required.

Decide from the outset on the type of installation (filtering or ducting). For greater efficiency, we recommend

you install the hood in the ducting version (if possible).

INSTALLATION

ATTENTION: The appliance should be installed by a qualified operator.

INSTALLATION IN DUCTING VERSION:

1. Before fixing, the disposal duct for air evacuation to the outside must be installed. Use an disposal duct

with: – minimum indispensable length; – minimum possible bends (maximum angle of bend: 90°); – certified material

(according to the State); – an as smooth as possible inside. It is also advisable to avoid any drastic changes

in pipe cross-section. We recommend using a 123 mm diameter pipe for models shown in Figures 3 and 4, and

a 150 mm diameter pipe for the model shown in Figure 5. For air evacuation to the outside, follow all the other

instructions given on the “Warnings” sheet.

2. Prepare a suitable power supply. For the electrical connection, follow all the other instructions on the

“Warnings” sheet.

3. Remove the metal grid or grease filters (make reference to Figures 6, 7 or 8 according to the model you

have purchased):

Fig. 6: remove the metal grid by moving the 2 side fasteners (A).

Fig. 7 and 8: remove the filter/s by moving fastener (B) and turning the filter outwards. Afterwards, remove

the metal grid by moving the 2 side fasteners (C).

4. Cut a hole in the bottom of the pensile cupboard in order to settle the appliance (Fig. 9).

5. To install the appliance, adjust the position of the clasping side spring by means of the proper screw

(Fig. 10D), according to the thickness of the bored panel to which it is going to be anchored.

Insert the appliance in the pensile cupboard and lock it by means of the side spring. Use the holes which

have already been made in the casing of the appliance to definitively fix it by means of 4 extra screws (provided)

- Fig.11.

6. Connect the disposal duct to the air evacuation pipe of the hood. Use a flexible pipe and lock it to the

air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make the electrical

connections.

7. Refit the metal grid and/or the grease filters.

INSTALLATION IN FILTERING VERSION:

Proceed with installation, making reference to the instructions for the extraction version (see points 2, 3, 4,

5), and then follow the instructions below.

Connect the hose to the hood air outlet so the air is conveyed to the top of the wall unit; secure the hose

with a metal clamp (hose and clamp are not provided). Make power connections.

Check whether the charcoal filters have already been fitted. If necessary, proceed to fit these as follows:

rest the charcoal filter on the motor unit by making the pins coincide; turn the charcoal filter until this is fast

(refer to Figures 12, 13 or 14 according to the model purchased).

Refit the metal grid and/or grease filters.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 15:

Key A = turns the lights on/off. Key B = turns the TIMER on/off: press once

to turn the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed blinks

on the display); the timer remains on if the motor speed is changed. Display C = - indicates the selected motor

speed (from 1 to 4); - indicates Timer On when the number blinks; - indicates Filter Alarm when the central segments

is on or blinking. Key D = makes the motor work (at the last speed selected); pushing the button again, the speeds

of the motor are sequentially selected from 1 to 4; keeping this button pressed for about 2 seconds shuts down

the motor. Key R = resets the grease filters or charcoal filters; when the filter alarm appears (i.e. when the central

segment on the display goes on), the grease filters must be cleaned (30 hours of operation); when the central

segment starts blinking, the grease filters must be cleaned and the charcoal filters replaced (120 hours of

operation). Obviously, if the hood is not a filtering model and does not have a charcoal filter, clean the grease

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-System MU-70 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info