Bedienungsanleitung Magnat QUANTUM 803 (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

581677

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Dear MAGNAT Customer,

Congratulationson yourfinenew loudspeakersandthankyouvery muchforchoosing MAGNAT!Youhave madeanexcellentchoice.The

high-quality speakers producedby MAGNATare renowned allover the world.

Please study theinstructions and informationbelow carefully before using yournew loudspeakers.

GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT QUANTUM 800 LOUDSPEAKERS

Warning

: Only hi-fi amplifier loudspeaker outputs may be connected to the Quantum 800 loudspeaker terminal.

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound quality, we

recommend cables withcross-sections of atleast 2.5 mm² for lengthsup to 3m and at least 4mm² for lengthsabove 3 m.

Always turn off the amplifier or receiver before connecting ordisconnecting loudspeaker cables. Place the loudspeakers in their planned

positions and cutthe cables tothe right length. Thecables for both channels shouldalways be exactlythe same length.

For good sound it is imperative that the cables must be connected in such a way that the speakers are “in phase”. This means that the

black negative terminalson the speakers (-)must be connectedto the negative (-)terminals on theamplifier,the redpositive (+) speaker

terminals to the positive (+) amplifier terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a

ridge in theinsulation.

The Quantum 800terminal is designedfor 3 cord sets:

Connection via bananaplugs (fig. 1a)

Connection via clevistype fittings (fig.1b)

Non-ready-made (fig. 1c):

Strip 10– 15 mmof insulation fromthe ends ofnon-ready-made cables.Twistthe ends– thisis much betterthan tinning themwith solder

– insert themin the terminalsand tighten the terminal screwsfirmly.

Before switchingon the systemdouble-check all your connectionsand makesure thatthe terminal screwsare tight and thatthere areno

short circuitscaused by straywire filaments – thiscould cause seriousdamage to your amplifier!

THE MAGNAT QUANTUM 800 LOUDSPEAKERS IN STEREO MODE

In the ideal configurationthe speakers and thelistening position should forman equilateral triangle. Whenthe left andright speakers are

the same distance from the listeningposition their soundarrives at the sametime, resulting in a harmonious,natural music reproduction.

(Fig. 2)

There should be a clear line of sightbetween the loudspeakers and the listening position.Any sound-absorbing or reflecting obstacles in

the pathwill distort thesound. When you installthe loudspeakers thefollowing distancesshould be maintained:

Quantum tower loudspeakers: atleast 20cm awayfrom therear walland atleast 30cm fromthe sidewalls.This willprevent excessive

emphasis of thebass range.

Quantum shelf-top loudspeakers: shelfloudspeakers should alsobe asfree-standingas possible,the distance to thesides and rearto

walls and itemsshould be atleast 10 cm, the tweetersshould be locatedat earheight.

MAGNAT QUANTUM 800 LOUDSPEAKERS AS A FRONT OR REAR LOUDSPEAKER

Thefrontloudspeakersarepositionedatearheightontheleftandrightasequidistantfromthetelevisionaspossible.Therearloudspeakers

are placed atear height ora little above on theleft andright besides or better behindthe listening position.

therwise all therecommendations made inthe previous chapter also apply.

ASSEMBLING THE SUPPLIED METAL SPIKES (QUANTUM 807, 805) (FIG. 3)

All ofthe speakersin theQuantum 800series areequipped withhigh-quality aluminiumfeet which ensurea securefooting in themajority

ofsituations.Thesuppliedmetalspikes,however,aremoreappropriateforsomefloorcoverings(e.g.carpets,unevenfloors,etc.).Athread

is incorporated inthe middle ofthe aluminium feet, into whichthe spikes canbe screwed.

Adjusttheheightoftheindividualspikessothatthespeakerstandsstraightandrigid(allfourspikesmusthavefirmcontactwiththeground).

The supplied socket wrench (wrench size 10) makes it easier to screw in the spikes. You can then tighten the locknut for the spikes by

using the othersocket wrench (wrenchsize 13).

MAGNAT QUANTUM 800 - BI-WIRING AND BI-AMPING

Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this idea one step further and uses

separate power amplifiers as well as separate cables for high and low frequencies. Bi-amping in particular produces an additional

improvement in soundreproduction quality.

The special connection terminalsof the Quantum 800loudspeakers support both conventionalconnection and operation inbi-wiring and

bi-amping modes. There are four screw terminals on each speaker. The top pair are for the tweeter (high frequencies), the lower pair for

thewoofer (lowfrequencies).The factory-installed cablesstripsconnecting thepositiveand negativeterminalsareforconventional 2-wire

connection and must be removed for bi-wiring and bi-amping operation. The pictures below show the correct set-up for conventional

operation (fig. 4a),bi-wiring (fig. 4b)and bi-amping (fig. 4c).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnat QUANTUM 803 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info