494155
6
Zoom out
Zoom in
Vorherige Seite
1/37
Nächste Seite
6
EN
Tilting the unit
You can adjust the base to change the angle of the unit
(-2° to 10°).
-2°
10°
Supplied Accessories
Owner’s Manual
(1EMN
26681
)
Quick Start Guide
(1EMN
26682
)
Remote Control
(NF804 UD)
Registration card
(1EMN
27079
)
AC power cord
(WAV0162LW001) or
(WAV0162LTE03) or
(WAV152ZHN001)
Batteries
(AAA, 1.5V x 2)
AAA
AAA
Screw kit
for attaching the base
(1ESA
25348
)
If you need to replace these accessories, please refer to
the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
Note
If you lose the screws, please purchase M 4×10 Phillips head screws at your
local store.
Symbols Used in this Manual
The following is the description for the symbols used in
this manual. Description refers to:
ATSC
: Digital TV operation
NTSC
: Analog / Cable TV operation
If neither symbol appears, the operation is applicable to both.
Attaching the Base
You must attach the base to the unit to have it as a table top
unit. Be sure the front and rear of the base match the proper
direction.
1 Spread a thick and soft
cloth over a table as
shown.
Place the main unit face
down onto it. Make sure
not to damage the screen.
2 Insert the metal neck
under the bottom of the
main unit into base holes.
(shown by arrow), then
move the base until it
stops and the 2 mounting
holes are aligned.
3 Drive Phillips head screws
into the 2 threaded holes
at the rear of this unit until
they are tight.
To remove the base from this unit
Unscrew the Phillips head screws on step 3.
After the screws are removed, move the base in the opposite direction on
step 2 to pull the base from the unit. Be careful not to drop the base when
you remove it.
Note
When attaching the base, ensure that all screws are tightly fastened. If the
base is not properly attached, it could cause the unit to fall, resulting in
injuries as well as damage to the unit.
Make sure to use a table which can support the weight of this unit and is
larger than this unit.
Make sure the table is in a stable location.
Fixing the Unit on Your Furniture
Screw this unit on your furniture tightly using wood screw (not
supplied) in the hole at the back of the base as shown.
Recommended screw dimension : 5.1 x 20 mm
screw hole
rear of this unit
Note
When you remove this unit make sure to unscrew the wood screw from
your Wood Stand, Furniture and other wood item.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Magnavox 22ME360B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info