Bedienungsanleitung Makita 1806B (Seite 4 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448166

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1 Knob

2 Switch trigger

3 Lock button/Lock-off button

4 Hex wrench

5Bolt

6 Adjusting screw

7 Planer blade

8 Notch in the blade

9 Drum cover

10 Drum

11 Triangular rule

12 Screwdriver

13 Nozzle

14 Vacuum cleaner

15 Start

16 End

17 Sharpening holder

18 Wing nut

19 Blade (A)

20 Blade (B)

21 Side (C)

22 Side (D)

23 Limit mark

24 Chip cover

25 Brush holder cap

SPECIFICATIONS

Model 1806B

Planing width .......................................................170 mm

Planing depth ..........................................................2 mm

No load speed (min

–1

) .......................................... 15,000

Overall length ......................................................529 mm

Net weight ..............................................................9.0 kg

Safety class........................................................... /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE001-1

Intended use

The tool is intended for planing wood.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

ENF100-1

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.41 Ohms it can be presumed that

there will be no negative effects.

The mains socket used for this device must be protected

with a fuse or protective circuit breaker having slow trip-

ping characteristics.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB010-4

PLANER SAFETY WARNINGS

1. Wait for the cutter to stop before setting the tool

down. An exposed cutter may engage the surface

leading to possible loss of control and serious injury.

2. Hold the power tool by insulated gripping sur-

faces only, because the cutter may contact its

own cord. Cutting a “live” wire may make exposed

metal parts of the power tool “live” and could give

the operator an electric shock.

3. Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body

leaves it unstable and may lead to loss of control.

4. Rags, cloth, cord, string and the like should

never be left around the work area.

5. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

6. Use only sharp blades. Handle the blades very

carefully.

7. Be sure the blade installation bolts are securely

tightened before operation.

8. Hold the tool firmly with both hands.

9. Keep hands away from rotating parts.

10. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

11. Make sure the blade is not contacting the work-

piece before the switch is turned on.

12. Wait until the blade attains full speed before cut-

ting.

13. Always switch off and wait for the blades to

come to a complete stop before any adjusting.

14. Never stick your finger into the chip chute.

Chute may jam when cutting damp wood. Clean

out chips with a stick.

15. Do not leave the tool running. Operate the tool

only when hand-held.

16. Always change both blades or covers on the

drum, otherwise the resulting imbalance will

cause vibration and shorten tool life.

17. Use only Makita blades specified in this manual.

18. Always use the correct dust mask/respirator for

the material and application you are working

with.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 1806B Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 1806B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info