Bedienungsanleitung Makita 4326 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

690955

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

11. Always switch off and wait for the blade to come

to a complete stop before removing the blade

from the workpiece.

12. Do not touch the blade or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

13. Do not operate the tool at no-load unnecessarily.

14. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

15. Always use the correct dust mask/respirator for

the material and application you are working

with.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

Selecting the cutting action (For models 4328/4329) (Fig. 1)

This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action

thrusts the blade forward on the cutting stroke and greatly increases cutting speed.

To change the cutting action, just turn the cutting action changing lever to the desired cutting action position.

Refer to the table to select the appropriate cutting action.

006582

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Speed adjusting dial (For models 4327/4328/4329)

(Fig. 3)

The tool speed can be infinitely adjusted between 500

and 3,100 strokes per minute by turning the adjusting

dial. Higher speed is obtained when the dial is turned in

the direction of number 6; lower speed is obtained when

it is turned in the direction of number 1.

Refer to the table to select the proper speed for the work-

piece to be cut. However, the appropriate speed may dif-

fer with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

006583

Position Cutting action Applications

0 Straight line cutting action

For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

I Small orbit cutting action For cutting mild steel, aluminum and hard wood.

II Medium orbit cutting action

For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

III Large orbit cutting action For fast cutting in wood and plywood.

Workpiece to be cut Number on adjusting dial

Wood 5 – 6

Mild steel 3 – 6

Stainless steel 3 – 4

Aluminum 3 – 6

Plastics 1 – 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4326 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info