Bedienungsanleitung Makita 5017 (Seite 5 von 18) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

110168

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

ENGLISH

Explanation of general view

1 A typical illustration of proper

hand support, workpiece sup-

port, and supply cord routing (if

applicable).

2 To avoid kickback, do support

board or panel near the cut.

3Don’t support board or panel

away from the cut.

4Hex wrench

5 Shaft lock

6Tighten

7 Loosen

8 Saw blade

9 Outer flange

10 Inner flange

11 Hex socket head bolt

12 Hex socket head bolt

(For adjusting riving knife)

13 Riving knife

14 Lever

15 Thumb nut

16 For 45° bevel cuts

17 For straight cuts

18 Base plate

19 Lock-off button

20 Switch trigger

21 Retracting lever

22 Safety cover

23 Guide rule

24 Notch

25 Cutting line

26 Dust cap

27 Rubber cap

28 Lever

29 Vacuum cleaner

30 Limit mark

31 Brush holder cap

32 Screwdriver

SPECIFICATIONS

Model 5017RKB

Blade diameter ....................................................190 mm

Max. cutting depth

At 90°.................................................................. 66 mm

At 45°.................................................................. 46 mm

No load speed (min

-1

).............................................. 4,800

Overall length ...................................................... 356 mm

Net weight............................................................... 5.5 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for performing lengthways and cross-

ways straight cuts and miter cuts with angles to 45° in

wood while in firm contact with the workpiece.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavour-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.35 Ohms it can be presumed that

there will be no negative effects.

The mains socket used for this device must be protected

with a fuse or protective circuit breaker having slow trip-

ping characteristics.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

SPECIFIC SAFETY RULES

GEB029-1

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to circular saw safety rules. If you use this tool

unsafely or incorrectly, you can suffer serious per-

sonal injury.

Danger:

1. Keep hands away from cutting area and the

blade. Keep your second hand on auxiliary han-

dle, or motor housing. If both hands are holding

the saw, they cannot be cut by the blade.

2. Do not reach underneath the workpiece. The

guard cannot protect you from the blade below the

workpiece. Do not attempt to remove cut material

when blade is moving.

CAUTION: Blades coast after turn off. Wait until

blade stops before grasping cut material.

3. Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

4. Never hold piece being cut in your hands or

across your leg. Secure the workpiece to stable

platform. It is important to support the work properly

to minimize body exposure, blade binding, or loss of

control. (Fig. 1)

5. Hold power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and shock the

operator.

6. When ripping always use a rip fence or straight

edge guide. This improves the accuracy cut and

reduces the chance of blade binding.

7. Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades

that do not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

8. Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation.

9. Causes and Operator Prevention of Kickback:

– kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the

operator;

– when the blade is pinched or bound tightly by the

kerf closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the

operator;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 5017 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info