Bedienungsanleitung Makita 6336D (Seite 5 von 64) (Alle Sprachen)

690553

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well venti-

lated area during charging.

ADDITIONAL SAFETY RULES FOR TOOL

ENB022-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a “live”

wire will also make exposed metal parts of the

tool “live” and shock the operator.

3. Always be sure you have a firm footing.

4. Be sure no one is below when using the tool in

high locations.

5. Hole the tool firmly.

6. Keep hands away from rotating parts.

7. Do not leave the tool running. Operate the tool

only when hand-held.

8. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Charging (Fig. 2)

Plug the battery charger into the proper A/C voltage source. The charging light will flash in green color. Insert the bat-

tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective

markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When

the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The

charging light will remain lit steadily during charging. When the charging light color changes from red to green, the

charging cycle is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the

charger will switch into its “trickle charge (maintenance charge)” mode. After charging, unplug the charger from the

power source.

Refer to the table below for the charging time.

CAUTION:

• The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufac-

turer’s batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

Battery type Capacity (Ah) Number of cells Charging time

1222 (Ni-cd) 2.0 10 Approx. 45 min.

1233 (Ni-MH) 2.2 10 Approx.50 min.

1234 (Ni-MH) 2.6 10 Approx.60 min.

1235 (Ni-MH) 3.0 10 Approx.70 min.

1422 (Ni-cd) 2.0 12 Approx. 45 min.

1433 (Ni-MH) 2.2 12 Approx.50 min.

1434 (Ni-MH) 2.6 12 Approx.60 min.

1435 (Ni-MH) 3.0 12 Approx.70 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6336D Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info