Bedienungsanleitung Makita 6805 bv (Seite 3 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

381496

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

Explanation of general view

1 Front cap

2 Locator

3 Pointer

4 Adjusting ring

5Low

6 High

7 Speed control screw

8 Switch trigger

9 Lock button

10 Reversing switch lever

SPECIFICATIONS

Model 6805BV

Capacities

Self drilling screw ...........................................6mm

Machine screw ...............................................8 mm

Wood screw ................................................6.2 mm

Bit shank size ............................................... 1/4” Hex

No load speed (min

–1

) ................................ 0 – 2,500

Overall length ................................................267mm

Net weight ........................................................ 1.9 kg

• Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

• Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

SPECIFIC SAFETY RULES

GEB017-1

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict

adherence to screwdriver safety rules. If you use

this tool unsafely or incorrectly, you can suffer

serious personal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

OPERATING INSTRUCTIONS

Removing or installing the bit (Fig.1)

Important:

Always be sure that the tool is switched off and

unplugged before removing or installing the bit.

To remove the bit, first pull the front cap off and then

pull the bit firmly. To install the bit, insert it into the

tool as far as it will go and then replace the front cap.

Depth adjustment (Fig.2,3 & 4)

When you wish to drive self drilling screws, etc.,

adjust the depth as follows. Turn the locator to adjust

the depth.

Initially, adjust the locator to create a distance of

approximately 1mm from the tip of the front cap

(which works in conjunction with the locator) to the

base of the screw head. One full turn of the locator

equals 1mm change in depth. After adjusting the

locator, turn the adjusting ring so that the 6" mark is

aligned with the pointer on the gear housing. Drive a

trial screw into your material or a piece of duplicate

material. If the depth is not suitable for the screw,

continue adjusting until the proper depth setting is

obtained.

Adjusting fastening torque (Fig. 5)

When you wish to drive tool screws, wood screws,

hex bolts, etc. with the predetermined torque, adjust

the fastening torque as follows. The fastening torque

may be adjusted by turning the adjusting ring. Before

turning the adjusting ring, turn the locator in the

direction of the arrow as far as it will go without forc-

ing. The torque is increased by turning the adjusting

ring in the direction of the arrow and decreased by

turning it in the opposite direction. Align the number 1

on the adjusting ring with the pointer on the gear

housing. Drive a trial screw into your material or a

piece of duplicate material. If the fastening torque is

not suitable for the screw, continue adjusting until the

proper torque is obtained.

CAUTION:

The adjusting ring should be turned only within the

numbered range. It should not be forced beyond this

range.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6805 bv Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info