Bedienungsanleitung Makita 6911 (Seite 5 von 10) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

381319

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

ADDITIONAL SAFETY RULES FOR TOOL

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Wear ear protectors.

3. Check the socket carefully for wear, cracks or

damage before installation.

4. Hold the tool firmly.

5. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

6. The proper fastening torque may differ depend-

ing upon the kind or size of the bolt. Check the

torque with a torque wrench.

7. When driving into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool only by the insulated grasping sur-

faces to prevent electric shock if you drive into a

“live” wire.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Charging (Fig. 2)

Plug the battery charger into the proper AC voltage source. The charging light will flash in green color. Insert the bat-

tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective

markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the

battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charg-

ing light will remain lit steadily during charging. When the charging light color changes from red to green, the charging

cycle is complete. Refer to the table below for the charging time. If you leave the battery cartridge in the charger after

the charging cycle is complete, the charger will switch into its “trickle charge (maintenance charge)” mode. After charg-

ing, unplug the charger from the power source.

CAUTION:

• The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufac-

turer’s batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location

exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a

while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the

battery cartridge from the fast charger.

• If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The ter-

minals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

• If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will

switch into its “trickle charge (maintenance charge)” mode and keep the battery cartridge fresh and fully charged.

Battery type Capacity (Ah) Number of cells Charging time

1202, 1202A, 1222 (Ni-cd) 2.0 10 Approx. 45 min.

1200, 1220 (Ni-cd) 1.3 10 Approx. 30 min.

1233 (Ni-MH) 2.2 10 Approx. 50 min.

1234 (Ni-MH) 2.6 10 Approx. 60 min.

1235 (Ni-MH) 3.0 10 Approx. 70 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6911 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info