Bedienungsanleitung Makita 8406 (Seite 5 von 19) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

387501

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

OPERATING INSTRUCTIONS

Side grip (auxiliary handle) (Fig. 1)

The position of the side grip can be changed in 30° incre-

ments. To change the position, loosen the side grip by

turning counterclockwise and slip out the side grip teeth

from the grooves on the tool. Swing the side grip to the

desired position and then slip the side grip teeth back

into the grooves on the tool. Then tighten the side grip

securely by turning clockwise.

Installing cover (optional accessory) (Fig. 2)

CAUTION:

When using a wet type of diamond core bit, always install

a cover (optional accessory) on the tool to thoroughly

protect the tool from water.

First, unplug the tool. Remove the grip base from the

tool. Install the cover on the tool so that the teeth on the

cover fit into the grooves on the tool. Then, install the

grip base on the tool and secure by tightening the side

grip firmly.

Installing or removing diamond core bit or drill bit

(Fig. 3)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each

of the three holes and tighten clockwise. Be sure to

tighten all three chuck holes evenly.

To remove the bit, turn the chuck key counterclockwise in

just one hole, then loosen the chuck by hand.

Depth gauge (Fig. 4)

The depth gauge is convenient for drilling holes of uni-

form depth. Insert the depth gauge into the hole in the

grip base and adjust the depth gauge to the desired

depth. Then tighten the clamp screw to secure the depth

gauge.

Switch action (Fig. 5)

To start the tool, simply pull the trigger. Release the trig-

ger to stop. The tool will not start if you turn on and off

instantly. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

CAUTION:

Before plugging in the tool, always check to see that the

trigger switch actuates properly and returns to the “OFF”

position when released.

Torque limiter

This tool is equipped with torque limiters. They will actu-

ate when a certain torque level is reached. When this

happens, the chuck will stop turning.

CAUTION:

• Do not continue to operate the tool for more than two

seconds while the torque limiter is actuating.

• Do not let the torque limiter actuates too frequently.

Speed change lever (Fig. 6)

Tool speed and number of blows per minute can be

adjusted in two ranges by turning the speed change

lever. For low speed, turn the speed change lever to the

“1” position. For high speed, turn the speed change lever

to the “2” position.

CAUTION:

Always set the speed change lever carefully into the cor-

rect position. If you operate the tool with the speed

change lever positioned half-way between the “1” posi-

tion and the “2” position, the tool may be damaged.

Speed adjusting dial (Fig. 7)

Tool speed can be infinitely adjusted from 900 to 4,000 min

–1

with the speed adjusting dial and speed change lever.

Numbers from 1 through 6 are indicated on the dial. Faster speeds are obtained by setting the dial to a higher number.

Number of blows per minute varies according to the tool speed. The following charts indicate resultant tool speeds in

various lever and dial positions explained above.

When the speed

change lever is

set to the “1” posi-

tion.

When the speed

change lever is set

to the “2” position.

Numbers on dial

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 8406 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info