390669
5
Zoom out
Zoom in
Vorherige Seite
1/7
Nächste Seite
OPERATING INSTRUCTIONS
Installing the wheel guard (Fig.1&2)
Important:
Always be sure that the tool is swiched off and
unplugged before installing or removing the wheel
guard.
Mount the wheel guard with the tab on the wheel
guard band aligned with the notch on the bearing box.
Then rotate the wheel guard 180° clockwise (for
9540) or counterclockwise (for 9541 and 9542). Be
sure to tighten the screw securely.
Side grip (auxialiary handle) (Fig. 3)
For your own safety, always use the side grip. The
side grip can be installed in any of three positions on
the sides of the tool.
Installing or removing the depressed center
wheel (Fig.4&5)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Mount the inner flange onto the spindle. Fit the wheel
on over the inner flange and screw the lock nut onto
the spindle. Press the shaft lock to prevent spindle
rotation, then use the lock nut wrench to tighten the
lock nut securely.
Warning:
Only actuate the shaft lock when the spindle is not
moving.
Switching ON and OFF (Fig. 6)
Caution:
Before plugging in the tool, always check to see that
the switch actuates properly and returns to the ‘OFF’’
position when the ‘‘O’ side of the switch lever is
depressed.
To switch on, depress the ‘‘O’’ side of the switch lever
and slide the switch lever toward the ‘‘I’’ position.
To switch off, depress the ‘‘O’’ side of the switch lever.
Operation (Fig. 7)
Keep the edge of the wheel or disc at an angle of
about 15° 30° to the workpiece surface. During the
break-in period with a new wheel, do not work the tool
in the B direction. It will cut into the workpiece. Once
the edge of the wheel has been rounded off by use,
the wheel may be worked in both A and B directions.
Warning:
It should never be necessary to force the tool. The
weight of the tool applies adequate pressure. Forc-
ing and excessive pressure could cause dangerous
wheel breakage.
Continued use of a worn-out wheel may result in
wheel explosion and serious personal injury.
Depressed center wheel should not be used after it
has been worn down to 75 mm for Model 9540 or
90 mm for Models 9541 and 9542 in diameter.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of carbon brushes (Fig. 8)
Whenever carbon brushes must be replaced, they cut
out the tool automatically. When this occurs, replace
both carbon brushes at the same time. Use only
identical carbon brushes.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by a
Makita Authorized Service Center.
9540 (’100. 12. 25)
5
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita 9541 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info