Bedienungsanleitung Makita 9911 (Seite 5 von 8) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

79030

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ENGLISH

Explanation of general view

1Lever

2 Steel plate

3 Adjusting screw

4 Dust bag

5 Dust spout

6 Lock button

7 Switch trigger

8 Speed adjusting dial

9 Clamps

10 Limit mark

11 Belt cover

12 Screwdriver

13 Brush holder cap

SPECIFICATIONS

Model 9910 9911

Belt size .......................................................................................76 mm x 457 mm 76 mm x 457 mm

Belt speed ....................................................................................270 m/min. 75 m – 270 m/min.

Overall length ..............................................................................262 mm 262 mm

Net weight ....................................................................................2.6 kg 2.6 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Hold the tool firmly with both hands.

3. Make sure the belt is not contacting the work-

piece before the switch is turned on.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. This tool has not been waterproofed, so do not

use water on the workpiece surface.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing abrasive belt (Fig. 1)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the belt.

Pull the lever all the way out and install the belt over the

rollers, then return the lever to the original position.

CAUTION:

When installing the belt, make sure that the direction of

the arrow on the back of the belt corresponds to the one

on the tool itself. (Fig.2)

Adjusting belt tracking (Fig. 3)

Switch on the tool and make sure that the belt is aligned

properly. If the edge of the belt extends beyond the edge

of the steel plate or the edge of the belt retracts more

than 8 mm away from the edge of the steel plate, use the

adjusting screw to adjust the belt tracking.

Dust bag (Fig. 4)

Attach the dust bag onto the dust spout. The dust spout

is tapered. When attaching the dust bag, push it onto the

dust spout firmly as far as it will go to prevent it from com-

ing off during operation. For the best results, empty the

dust bag when it becomes about half full, tapping it lightly

to remove as much dust as possible.

Switch action (Fig. 5)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• The tool should not be in contact with the workpiece

surface when you turn the tool on or off. Otherwise a

poor sanding finish or damage of the belt may result.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 9911 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info