598398
6
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
6
ENGLISH
Explanation of general view
1 Compressor air output per
minute
2 Nailing frequency (times/min.)
3Adjuster
4 Shallow
5Deep
6 Too deep
7Flush
8 Too shallow
9Hook
10 Hole
11 Protrusion
12 Nose adapter
13 Magazine cap
14 Latch lever
15 Door
16 Adjustfit
17 Change plate
18 Arrow
19 Nail guide
20 Feeder
21 Trigger
22 Contact element
23 Change lever
24 0.7 mm or less thick for steel
plate
25 Thickness of workpiece
26 10 mm or more
27 C-shaped steel
(Thickness 1.6 mm – 2.3 mm)
28 Nail driven to a proper depth
29 Nail driven too deep will cause
deformation of workpieces
30 Nail length
31 Wood thickness
32 Concrete range 10 – 15 mm
33 Small rod
34 Screwdriver
35 Cap
36 Drain cock
37 Air filter
38 Oiler
39 Pneumatic oil
SPECIFICATIONS
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2” x 4” housing.
IMPORTANT SAFETY INSTRUCTIONS
ENB109-1
WARNING:
WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and mainte-
nance of the tool, read this instruction manual before
using the tool.
Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
• Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or rolled
up. No necktie should be worn.
Rushing the job or forcing the tool is dangerous. Han-
dle the tool carefully. Do not operate when under the
influence of alcohol, drugs or the like.
General Tool Handling Guidelines:
1. Always assume that the tool contains fasteners.
2. Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
3. Do not activate the tool unless the tool is placed
firmly against the workpiece.
4. Respect the tool as a working implement.
5. No horseplay.
6. Do not hold or carry the tool with a finger on the
trigger.
7. Do not load the tool with fasteners when any one of
the operating controls is activated.
8. Do not operate the tool with any power source other
than that specified in the tool operating/safety
instructions.
An improperly functioning tool must not be used.
Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as gas-
oline, thinner, paint, gas, adhesives, etc.; they will ignite
and explode, causing serious injury.
Model AN610H
Air pressure 0.98 – 2.26 MPa (9.8 – 22.6 bar)
Nail length
Wire-collated coil nail 32 mm – 65 mm
Sheet-collated coil nail 32 mm – 65 mm
Nail capacity
Wire-collated coil nail 250 pcs, 300 pcs, 400 pcs
Sheet-collated coil nail 200 pcs
Min. hose diameter 5.0 mm
Dimensions (L x H x W) 282 mm x 277 mm x 136 mm
Net weight 1.9 kg
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita AN610H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info