601101
4
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
4
ENGLISH
Explanation of general view
3-1. Pneumatic tool oil
4-1. Adjuster
5-1. Change lever
5-2. Plastic collated coil
5-3. Wire collated coil
6-1. Door
6-2. Magazine cap
6-3. Lever
7-1. Graduation
7-2. Coil support plate
8-1. Slot
8-2. Magnet
8-3. Feeder body
9-1. Air socket
9-2. Air fitting
10-1. Trigger
10-2. Contact element
12-1. Continuous nailing
12-2. Change lever
12-3. Trigger lock
13-1. Exhaust cover
14-1. Small rod
14-2. Ejection port
15-1. Hook
18-1. Change lever
18-2. Trigger lock
19-1. Cap
22-1. Magnet
23-1. Drain cock
24-1. Air filter
25-1. Oiler
25-2. Pneumatic oil
SPECIFICATIONS
Model AN621
Air pressure 0.44 - 0.83 Mpa (4.4 - 8.3 bar)
Wire welded nails 45 mm - 65 mm
Applicable length
Plastic sheet collated nails 50 mm - 65 mm
Nail capacity 200 - 300 pcs.
Min. hose diameter 6.5 mm
Pneumatic tool oil Turbine oil
Dimensions (L X H X W) 310 mm X 305 mm X 133 mm
Net weight 2.8 kg
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
END105-1
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Wear safety glasses.
ENE059-1
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2 “x 4” housing.
ENG046-1
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 86 dB (A)
sound power level: 99 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is 6 m/s
2
.
These values have been obtained according to EN792.
ENH013-7
EC-DECLARATION OF CONFORMITY
Model; AN621
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN792 in accordance with Council Directives, 98/37/EC.
CE2008
000230
Tomoyasu Kato
Director
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
ENB067-2
IMPORTANT SAFETY
INSTRUCTIONS
WARNING: WHEN USING THIS TOOL, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and
maintenance of the tool, read this instruction
manual before using the tool.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita AN621 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info