598453
6
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
6
LED indicator / Beeper (Fig. 5)
LED indicator / Beeper on the tool shows the following functions.
Status of
the LED indicator/beeper
Function Status Action to be taken
LED indicator Beeper
Lights up in
Green
Red
Blue
White in order.
A series of very
short beeps
Check LED, light
and beeper
(when pulling
switch trigger for
the first time after
installing a battery
cartridge into the
tool).
Make sure that green, red,
blue, white LED lights up
and beeper beeps properly.
__
Lights up in green
for approximately
one second.
__
Auto-stop
fastening
This function works when
the tool has reached the
preset fastening torque
and normal tightening has
been completed. This
helps overtightening to be
avoided.
__
Blinks in purple
slowly.
A series of long
beeps
Warning for battery
cartridge capacity
This indicates the
appropriate time to replace
the battery cartridge when
the battery power
becomes low.
Replace the battery
with fully charged one.
Lights up in purple. A long beep
Checking the
remaining battery
capacity, Autostop
This function works when
the battery power is almost
used up. At this time, tool
stops immediately.
Replace the battery
with fully charged one.
Lights up in red and
green alternatively.
A series of short
beeps
Anti-reset of
controller
This function works when
an abnormal drop of the
battery voltage occurs for
some reason and the tool
stops.
Replace the battery
with fully charged one.
Failure of motor
This function works when
motor fails.
Take it to a Makita
Authorized Service
centers.
Blinks in red quickly.
A series of short
beeps
Overheat
This function works when
the temperature of the
controller or motor goes up
very highly, and the tool
stops.
Remove the battery
cartridge immediately
and cool the tool
down.
Blinks in red and
yellow alternatively.
A long beep
Warning against
insufficient fasten-
ing
Fastening is incomplete
when switch trigger of tool
is released before clutch
activation.
__
Double-hitting
detection
This function works when
a screw is refastened after
fastening.
__
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita BFL301F wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info