Bedienungsanleitung Makita BJN161 (Seite 7 von 12) (Englisch, Holländisch)

598571

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

To start the tool, slide the slide switch toward the “I (ON)”

position. For continuous operation, press the front of the

slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

Indication lamp with multi function (Fig. 5)

Indication lamps are located in two positions.

- Battery cartridge replacing signal

- When the battery power is almost used up during

operation, the red lamp lights up and the tool stops

immediately. Replace the battery with fully charged

one when the red lamp lights up.

- Accidental re-start preventive function

- Even if the battery cartridge is inserted on the tool

with the slide switch in the “I (ON)” position, the tool

does not start. At this time, the lamp flickers slowly

and this shows that the accidental re-start preventive

function is at work.

- To start the tool, first slide the slide switch toward the

“O (OFF)” position and then slide it toward the “I

(ON)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Removing or installing the punch and die (Fig. 6,

7, 8 & 9)

Always replace the punch and die as a set. To remove

the punch and die, loosen the lock nut with the wrench.

Remove the die holder from the tool. Use the hex wrench

to loosen the bolts which secure the die. Remove the die

from the die holder.

Use the hex wrench to loosen the screw which secures

the punch. Pull the punch out of the punch holder.

To install the punch and die, insert the punch into the

punch holder so that the notch in the punch faces toward

the screw. Tighten the screw to secure the punch. Install

the die on the die holder. Tighten the bolts to secure the

die.

Then install the die holder on the tool so that the punch is

inserted through the hole in the die holder. Tighten the

lock nut to secure the die holder. After replacing the

punch and die, lubricate them with machine oil and run

the tool for a while.

OPERATION

Pre-lubrication

Coat the cutting line with machine oil to increase the

punch and die service life. This is particularly important

when cutting aluminum.

Cutting method (Fig. 10)

Hold the tool so that the cutting head is at a right angle

(90°) to the workpiece being cut. Move the tool gently in

the cutting direction.

Cutouts (Fig. 11)

Cutouts can be done by first opening a round hole over

21 mm in diameter which the cutting head can be

inserted into.

Cutting the corrugated or trapezoidal sheet

metals (Fig. 12 & 13)

Set the die position so that the die faces the cutting direc-

tion either when cutting at an angle or perpendicular go

grooves in corrugated or trapezoidal sheet metals.

Always hold the tool body parallel to the grooves with the

cutting head at a right angle (90°) to the cutting surface

as shown in the figure.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 14, 15 & 16)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it

up.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Reinstall the holder cap cover on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Die

• Punch

• Hex wrench

• Wrench 32

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BJN161 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info