Bedienungsanleitung Makita BTD042 (Seite 6 von 10) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

598603

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Confirming the presetting

Switch off the tool and insert the battery cartridge. The indicating lamp will indicate the presetting number.

Green lamp shows the first digit. Red lamp shows the second digit.

Example: Presetting number is 12.

Green color lamp flashes once.  Red color lamp flashes two times.  The lamp goes out.

Relation between presetting number and action

Indicating lamp

• After impacting preset numbers, the indicating lamp

lights in green color.

• The red color light will light on if the trigger is pulled

before the presetting number of impacts is achieved. It

indicates that the operation is incomplete.

Operation (Fig. 10, 11, 12 & 13)

[*1] Presetting number of impacts is impossible for more

than 200 impacts (4 seconds).

[*2] Fastening time includes when you pull the trigger

completely.

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in Fig. 10 & 12

for standard bolt or Fig. 11 & 13 for high tensile bolt.

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Hold the tool pointed straight at the screw.

• If you tighten the screw for a time longer than shown in

the figures, the screw or the point of the driver bit may

be overstressed, stripped, damaged, etc. Before start-

ing your job, always perform a test operation to deter-

mine the proper fastening time for your screw.

• If the tool is operated continuously, allow the tool to rest

for 15 minutes before proceeding with a fresh battery.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work on

the tool.

Replacement of carbon brushes (Fig. 14 & 15)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Bit-piece

• Protector (clear, red, blue)

• Various type of Makita genuine batteries and chargers

• Automatic refreshing adapter

Presetting

number

Clockwise rotation Counterclockwise rotation

00 Auto-stop setting does not work. Auto-stop setting does not work.

01 – 99

After impacting [number of impacts

(presetting number x 2) x 0.02] seconds

 Green color lamp lights on.

Switch off before impacting [number of impacts (preset-

ting number x 2) x 0.02] seconds

 Red color lamp lights on. Then, the lamp will go out.

Auto-stop setting does not work.

Indication lamp goes out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTD042 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info