600556
5
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
5
ENGLISH (Original instructions)
Explanation of general view
1 Red indicator
2 Button
3 Battery cartridge
4 Star marking
5 Thumb screw
6Shoe
7 Slide switch
8 Collet nut
9Shaft lock
10 Tighten
11 Loosen
12 Collet cone
13 Bit
14 Projections
15 Circular guide
16 Knob
17 Vacuum cover
18 Tool
19 Hose 28
20 Hose for vacuum cleaner
21 Vacuum cleaner
22 Dust collector
23 Limit mark
24 Holder cap cover
25 Screwdriver
26 Brush holder cap
SPECIFICATIONS
Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
Specifications and battery cartridge may differ from
country to country.
Weight, with battery cartridge, according to EPTA-
Procedure 01/2003
ENE012-1
Intended use
The tool is intended for cutting gypsum, wood, plastic
and soft wall tiles.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
GEB123-1
CORDLESS CUT-OUT TOOL SAFETY
WARNINGS
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
3. Wear eye protection and dust mask.
4. Ventilate your work area adequately.
5. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
6. Check for the proper clearance beneath the
workpiece before cutting so that the bit will not
strike a hard surface such as the floor,
workbench, etc.
7. Do not cut metal objects such as nails and
screws. Inspect for and remove all nails, screws
and other foreign material from the workpiece
before operation.
8. Check that the bit is not contacting the
workpiece before the switch is turned on.
Always hold the tool with two hands while
switching the tool on. The motor torque can
cause the tool to turn.
9. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
10. Make sure that the shaft lock is released before
the switch is turned on.
11. Always use with the shoe securely attached to
the tool and positioned flat and firmly against
the workpiece.
12. Hold the tool firmly.
13. Do not perform any operation using your hands
to support or guide the workpiece.
14. Keep hands away from moving parts.
15. Do not use this tool for drilling.
16. Do not leave the tool running. Operate the tool
only when hand-held.
17. Always switch off and wait for the bit to come to
a complete stop before removing the bit from
workpiece.
18. Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
19. Draw attention to the need to use cutters of the
correct shank diameter and which are suitable
for the speed of the tool.
SAVE THESE INSTRUCTIONS.
Model DCO140 DCO180
Collet chuck capacity 3 mm, 6 mm or 1/8", 1/4" 3 mm, 6 mm or 1/8", 1/4"
Rated speed (n)/ No load speed (n
0
) 30,000 min
–1
30,000 min
–1
Overall length 313 mm 313 mm
Net weight 1.6 kg 1.7 kg
Rated voltage D.C. 14.4 V D.C. 18 V
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita DCO180 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info