Bedienungsanleitung Makita DP2011 (Seite 3 von 32) (Deutsch, Englisch, Polnisch)

600288

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1-1. Switch trigger

1-2. Lock button

2-1. Speed control screw

2-2. Higher

2-3. Lower

3-1. Reversing switch

4-1. Tighten

4-2. Chuck key

5-1. Sleeve

5-2. Ring

6-1. Depth gauge

6-2. Washer

6-3. Clamp screw

SPECIFICATIONS

Model DP2010 DP2011

Steel 6.5 mm 6.5 mm

Capacities

Wood 15 mm 15 mm

No load speed (min

-1

) 0 - 4,200 0 - 4,200

Overall length 209 mm 222 mm

Net weight 1.0 kg 1.1 kg

Safety class /II /II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE032-1

Intended use

The tool is intended for drilling in wood, metal and

plastic.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They

are double-insulated and can, therefore, also be used

from sockets without earth wire.

ENG905-1

Noise

The typical A-weighted noise level determined

according to EN60745:

Sound pressure level (L

) : 77 dB(A)

Uncertainty (K) : 3 dB(A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum)

determined according to EN60745:

Work mode: drilling into metal

Vibration emission (a

h,D

) : 4.0 m/s

Uncertainty (K) : 1.5 m/s

ENG901-1

•

The declared vibration emission value has been

measured in accordance with the standard test

method and may be used for comparing one tool

with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission

value depending on the ways in which the tool is

used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).

ENH101-16

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

High Speed Drill

Model No./ Type: DP2010, DP2011

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745

The technical documentation is kept by:

Makita International Europe Ltd.

Technical Department,

Michigan Drive, Tongwell,

Milton Keynes, Bucks MK15 8JD, England

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DP2011 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DP2011

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info