Bedienungsanleitung Makita DUB361 (Seite 6 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599992

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Tool/battery protection system

The tool is equipped with a tool/battery protection

system.

This system automatically cuts off power to the motor to

extend tool and battery life.

The tool will automatically stop during operation if the

tool or battery are placed under one of the following

conditions. In some conditions, the indicators light up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indication. In this situation, turn the tool

off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for battery

When the battery is overheated, the tool stops

automatically without any indication. The tool does not

start even if pressing the switch button. In this situation,

let the battery cool before turning the tool on again.

NOTE:

• The battery overheat protection works only with a

battery cartridge with a star marking. (Fig. 2)

Overdischarge protection (Fig. 3)

When the remaining battery capacity gets low, the

battery indicator blinks on the applicable battery side. By

further use, the tool stops and the battery indicator lights

up about 10 seconds. In this situation, charge the battery

cartridge.

Switch action (Fig. 4)

To start the tool, simply press the “HIGH/LOW” button. To

switch off, press the “OFF” button. To change the tool

speed, press the “HIGH/LOW” button. The first press on

this button is for high speed and the second press for low

speed and then each press on this button repeats the

high/low speed cycle alternatively.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing the long nozzle (Fig. 5 & 6)

To install the long nozzle, push in onto the blower outlet

of the tool all the way.

To remove the long nozzle, press its both buttons and

with the buttons being pressed pull it out.

Installing the shoulder strap (Fig. 7)

Pull the hanger out of the tool.

Hook the shoulder strap onto the hanger of the tool.

Before use, adjust the length of strap so that it is easy to

work with it.

OPERATION

Blowing (Fig. 8)

Hold the blower firmly with a hand and perform the

blowing operation by moving it around slowly.

When blowing around a building, a big stone or a vehicle,

direct the nozzle away from them.

When performing an operation in corner, start from the

corner and then move to wide area.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Cleaning (Fig. 9)

From time to time, wipe off the outside of the tool using a

cloth dampened in soapy water.

Replacing carbon brushes (Fig. 10 & 11)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

ENG102-3

Noise

The typical A-weighted noise level determined according

to EN15503:

Sound pressure level (L

): 82.3 dB (A)

Sound power level (L

): 94.7 dB (A)

Uncertainty (K): 1.6 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN15503:

Work mode: operation without load

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUB361 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info