599765
5
Zoom out
Zoom in
Vorherige Seite
1/108
Nächste Seite
5
ENGLISH (Original instructions)
Explanation of general view
1Shaft lock
2 Slide switch
3 Wheel guard
4 Bearing box
5Screw
6 Lever
7 Lock nut
8 Depressed center wheel
9 Inner flange
10 Lock nut wrench
11 Ezynut
12 Abrasive wheel
13 Spindle
14 Arrow
15 Notch
16 Flex wheel
17 Plastic pad
18 Sanding lock nut
19 Abrasive disc
20 Rubber pad
21 Marking A
22 Marking B
23 Marking C
24 Marking D
25 Abrasive cut-off wheel/diamond
wheel
26 Wheel guard for abrasive cut-off
wheel/diamond wheel
27 Wire cup brush
28 Wire wheel brush
29 Exhaust vent
30 Inhalation vent
SPECIFICATIONS
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
ENE048-1
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
GEB033-7
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
Model GA4040 GA4540 GA5040 GA6040
Wheel diameter 100 mm (4") 115 mm (4-1/2") 125 mm (5") 150 mm (6")
Max. wheel thickness 6.4 mm
Spindle thread M10 M14 or 5/8" (country specific)
Rated speed (n) /
No load speed (n
0
)
11,000 min
–1
11,000 min
–1
11,000 min
–1
9,000 min
–1
Overall length 303 mm 303 mm 303 mm 303 mm
Net weight 2.3 kg 2.4 kg 2.4 kg 2.5 kg
Safety class /II
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita GA5040 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info