599703
5
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
5
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Symbols
END202-7
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
...... Read instruction manual.
................ DOUBLE INSULATION
...... Wear safety glasses.
................ Only for EU countries
Do not dispose of electric equipment
together with household waste
material!
In observance of European Directive
2012/19/EU on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
Intended use
ENE050-1
The tool is intended for grinding ferrous materials or
deburring castings.
Power supply
ENF002-2
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings GEA010-1
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
STRAIGHT GRINDER SAFETY
WARNINGS
GEB108-3
Safety Warnings Common for Grinding Operation:
1. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
1. Switch trigger
2. Lock lever
3. Hex wrench
4. Hex bolt
5. Hex lock nut
6. Tighten
7. Loosen
8. Wing bolt
9. Support cover
10. Lock nut
11. Grinding wheel
12. Spindle
13. Screwdriver
14. Inner flange
15. Lock nut wrench
16. Hex nut
17. Outer flange (convex type)
18. Outer flange (flat type)
19. Exhaust vent
20. Inhalation vent
21. Handle R
22. Dust cover attachment R
23. Handle L
24. Dust cover attachment L
25. Hook B
26. Hook A
27. Rib A
28. Vent A
29. Vent B
30. Commutator
31. Insulating tip
32. Carbon brush
33. Brush holder cap
Model GS5000 GS6000
Maximum wheel capacity (diameter thickness) 125 mm 20 mm 150 mm 20 mm
Spindle thread M14 or 1/2” (country specific)
No load speed (min
-1
) 5,600
Overall length
With support cover 590 mm 590 mm
Without support cover 588 mm 588 mm
Net weight
With support cover 5.0 kg 5.2 kg
Without support cover 4.9 kg 5.0 kg
Safety class /II
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita GS6000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info