Bedienungsanleitung Makita HR 2010 (Seite 4 von 14) (Englisch, Holländisch)

448521

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3Bit

4 Chuck cover

5 Side grip

6 Loosen

7 Tighten

8 Grip base

9 Clamp screw

10 Depth gauge

11 Switch trigger

12 Chuck adapter

13 Drill chuck

14 Screw driver

15 Brush holder cap

16 Lock nut wrench

17 Crank cap

18 Hammer grease

SPECIFICATION

Model HR2010

Capacities

Concrete ............................................................ 20 mm

Wood ................................................................. 24 mm

Steel .................................................................. 13 mm

No load speed (min

–1

).......................................... 0 – 900

Blows per minute .............................................. 0 – 4,000

Overall length ...................................................... 302 mm

Net weight ............................................................. 3.2 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

SPECIFIC SAFETY RULES

GEB007-2

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to rotary hammer safety rules. If you use this tool

unsafely or incorrectly, you can suffer serious per-

sonal injury.

1. Wear ear protectors. Exposure to noise can cause

hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before opera-

tion.

6. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a

while by operating it under no load. This will

loosen up the lubrication. Without proper warm-

up, hammering operation is difficult.

8. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

9. Hold the tool firmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

14. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Installing or removing drill bit (Fig. 1, 2 & 3)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 1)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 2)

If the bit cannot be pushed in, remove the bit. Pull the

chuck cover down a couple of times. Then insert the bit

again. Turn the bit and push it in until it engages. (Fig. 3)

After installing, always make sure that the bit is securely

held in place by trying to pull it out. To remove the bit, pull

the chuck cover down all the way and pull the bit out.

Side grip (Auxiliary handle) (Fig. 4)

The side grip swings around to either side, allowing easy

handling of the tool in any position. Loosen the side grip

by turning it counterclockwise, swing it to the desired

position and then tighten it by turning clockwise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR 2010 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita HR 2010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info