Bedienungsanleitung Makita hr 2400 (Seite 5 von 32) (Deutsch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388817

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Operating instruction (Fig. 5)

Important:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

Switching ON and OFF (Fig. 5)

To switch on, press the trigger.

To switch off, release the trigger.

Continuous running (Fig. 5)

Press the trigger and at the same time slide the lock

lever upward. To stop from this lock position, press

the trigger and release it.

Variable trigger speed control (Fig. 5)

The speed varies from 0 to maximum, depending on

the pressure applied to the trigger. The more the

trigger is pressed, the faster the machine runs.

Reversing switch (Fig. 5)

Important:

Only reverse the direction of rotation when the motor

stops completely.

To change the direction of rotation:

Position FWD: right hand rotation

Position REV: left hand rotation

Three selecting action modes (Fig. 6)

For hammer drilling:

Turn the knob so that the arrow points toward the

symbol.

For drilling only:

Turn the knob so that the arrow points toward the

symbol.

For hammering only:

Turn the knob so that the arrow points toward the

symbol.

NOTE:

When it is hard to turn the knob, pull the switch trigger

half-way for running at low speed and turn the knob.

Torque limiter

The torque limiter will actuate when a certain torque

level is reached. The motor will disengage from the

output shaft. When this happens, the bit will stop

turning.

CAUTION:

As soon as the torque limiter actuates, switch off the

machine immediately. This will help prevent prema-

ture wear of the machine. Hole saws, core bit, dia-

mond core bit, etc. cannot be used with this machine.

They tend to pinch or catch easily in the hole. This will

cause the torque limiter to actuate too frequently.

Using cold chisel or bull point (Fig. 7)

1. Disconnect plug.

2. Remove the side grip from the machine.

3. Turn the knob to hammer drilling symbol

4. Install the cold chisel or bull point and then the

chisel adapter (optional accessory) on the

machine.

5. Rotate the cold chisel toward the direction suitable

for your work. Then secure the cold chisel and

chisel adapter by using the clamp screw on the

chisel adapter.

6. Turn the knob to hammering only symbol

Now you can use the cold chisel or bull point.

NOTE:

Always set ‘‘hammering only’’ action when using the

cold chisel or bull point. If you use ‘‘hammer drilling’’

or ‘‘drilling only’’ action, the hammering mechanism

may be damaged on the machine.

Drilling in wood or metal (Fig. 8)

Use the optional drill chuck assembly (consisting of

drill chuck and chuck adapter assembly). When

installing it, refer to ‘‘installing or removing drill bit’’

described on the previous page. Set the knob to

‘‘drilling only’’. You can drill up to 13 mm diameter in

metal and up to 38 mm diameter in wood. (Note:

When using a flat boring bit.)

NOTE:

Never set ‘‘hammer drilling’’ action when using the

drill chuck assembly because it may be damaged and

come off when reversing the machine.

MAINTENANCE

CAUTION:

Always be sure that the machine is switched off and

unplugged before carrying out any work on the

machine.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

Makita Authorized Service Center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita hr 2400 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita hr 2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info