Bedienungsanleitung Makita JR 3030 (Seite 5 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448559

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

Explanation of general view

1 Blade

2 Push button

3 Hex wrench 4

4 Loosen

5 Tighten

6 Pin

7 Screw

8 Slider

9 Blade clamp

10 Hole

11 Lever

12 Shoe

13 Switch trigger

14 Lock button/Lock-off button

15 Limit mark

16 Screwdriver

17 Brush holder cap

SPECIFICATIONS

Model JR3030 JR3030T

Length of stroke .......................................................... 28 mm 28 mm

Strokes per minute ..................................................... 0 – 2,600 0 – 2,600

Cutting capacities

Pipe .......................................................................... 90 mm 90 mm

Wood ........................................................................ 90 mm 90 mm

Overall length ............................................................. 438 mm 460 mm

Net weight ................................................................... 3.5 kg 3.5 kg

• Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

• Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear pro-

tectors and thickly padded gloves.

2. Check the blade carefully for cracks or dam-

age before operation. Replace cracked or

damaged blade immediately.

3. Do not attempt to cut workpieces larger than

specified in this manual (especially hollow

pipe). The blade might snap and cause an

injury. (Fig. 1)

4. Hold the tool firmly.

5. Be sure no one is below when using the tool in

high locations.

6. Do not point the tool at anyone in the immedi-

ate vicinity.

7. When making a ‘‘blind’’ cut (you can’t see

behind what is being cut), be sure that hidden

electrical wiring or water pipes are not in the

path of the cut. If wires are present, they must

be disconnected at their power source by a

qualified person or avoided to prevent the

possibility of lethal shock or fire. Always hold

the tool ONLY by the insulated gripping sur-

faces to prevent any electric shock if you

accidentally cut through a ‘‘live’’ wire. Water

pipes in ‘‘blind’’ areas must be drained and

capped before cutting.

8. Be careful not to hit the end of the blade

against something during operation. Damage

to the tool or dangerous blade breakage may

occur. (Fig. 2)

9. Watch out for cut-off portions of the workpiece

being cut. They may fall and injure you or

someone near you.

10. When cutting metals, be cautious of hot flying

chips.

11. Do not touch the blade or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

12. If you withdraw the blade from the workpiece

during operation, strong reaction will be pro-

duced, causing the blade to snap or causing

you to lose your grip and control of the tool.

Always switch off the tool and wait until the

blade has come to a complete stop before

withdrawing the blade from the workpiece.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing saw blade

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Always clean out all chips or foreign matter adher-

ing to the blade, blade clamp and/or slider. Failure

to do so may cause insufficient tightening of the

blade, resulting in a serious injury.

JR3030 (E) (’101. 1. 9)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JR 3030 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita JR 3030

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info