Bedienungsanleitung Makita jr 3060 t (Seite 5 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

383461

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting the shoe (Fig. 1 & 2)

When the blade loses its cutting efficiency in one place

along its cutting edge, reposition the shoe to utilize a

sharp, unused portion of its cutting edge. This will help to

lengthen the life of the blade. To reposition the shoe, push

the shoe button in the “A” direction with a click and

reposition as shown in the figure which allows you to

make five-way adjustment. To secure the shoe, push the

shoe button in the “B” direction with a click.

Selecting the cutting action (Fig. 3)

This tool can be operated with an orbital or a straight line

cutting action. The orbital cutting action thrusts the blade

forward on the cutting stroke and greatly increases cutting

speed.

To change the cutting action, press the stopper and turn

the lever to the desired cutting action position. Then,

release the stopper to lock the lever. Refer to the table to

select the appropriate cutting action.

NOTE:

• Orbital action means that the saw blade moves up and

down, and back and forth at the same time. This

increases the efficiency of cutting.

002525

Switch action (Fig. 4)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop. For continuous

operation, pull the switch trigger and then push in the lock

button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Speed adjusting dial (For JR3070CT)

(Fig. 5)

The strokes per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 6 (full

speed). Turn the adjusting dial without positive stops

between 1 and 6 according to your work.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed may

differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

006574

006584

NOTE:

• If the tool is operated continuously at low speeds for a

long period of time, the operation life of the motor will

be reduced.

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

The tools equipped with electronic function are easy to

operate because of the following features.

Position Cutting action Applications

Straight line cutting

action

For cutting mild steel,

stainless steel and

plastics.

For clean cuts in

wood and plywood.

Small orbit cutting

action

For cutting mild steel,

aluminum and hard

wood.

Medium orbit cutting

action

For cutting wood and

plywood.

For fast cutting in

aluminum and mild

steel.

III

Large orbit cutting

action

For fast cutting in

wood and plywood.

Number on adjusting dial Strokes per minute

6 2,800

5 2,500

4 1,850

3 1,400

2 1,000

1950

Workpiece to be cut Number on adjusting dial

Wood 6

Autoclaved lightweight

concrete

5 - 6

Mild steel 3 - 4

Aluminum 3 - 5

Plastics 1 - 4

Stainless steel 1 - 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita jr 3060 t Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita jr 3060 t

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info