Bedienungsanleitung Makita JR3000 (Seite 3 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

599030

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

Explanation of general view

1 Hex wrench

2 Bolt

3 Shoe

4 Bolt

5 Speed change switch

6 Switch trigger

7 Lock button/Lock-off button

8 Speed control screw

9 High

0 Low

q Limit mark

w Brush holder cap

e Screwdriver

SPECIFICATIONS

Model JR3000 JR3000V

Length of stroke .......................................................................... 30 mm 30 mm

Strokes per minute ...................................................................... Hi : 2,500 Low : 1,900 0 – 2,300

Overall length .............................................................................. 400 mm 400 mm

Net weight ................................................................................... 2.9 kg 2.9 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed Safety

instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

2. Do not cut oversize workpiece.

3. Check for the proper clearance beyond the

workpiece before cutting so that the blade will

not strike the floor, workbench, etc.

4. Hold the machine firmly.

5. Make sure the blade is not contacting the

workpiece before the switch is turned on.

6. Keep hands away from moving parts.

7. When cutting through walls, floors or wher-

ever ‘‘live’’ electrical wires may be encoun-

tered, DO NOT TOUCH ANY METAL PARTS OF

THE MACHINE! Hold the machine by the insu-

lated grasping surfaces to prevent electric

shock if you cut through a ‘‘live’’ wire.

8. Do not leave the machine running. Operate the

machine only when hand-held.

9. Always switch off and wait for the blade to

come to a complete stop before removing the

blade from the workpiece.

10. Do not touch the blade or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing saw blade (Fig. 1)

Important:

Always be sure that the machine is switched off and

unplugged before installing or removing the blade.

First, use the hex wrench to loosen the bolt. With the

blade teeth facing upward or downward, insert the

blade until the hole in the blade shank is just over the

protrusion on the slider. Then tighten the bolt to

secure the blade.

Adjusting shoe (Fig. 2)

Loosen the two bolts holding the shoe. Then slide the

shoe back or forth to the desired position and tighten

the two bolts securely. When the blade loses its

cutting effectiveness in one place, reposition the shoe

to obtain better cutting in another.

Speed change (For JR3000 only) (Fig. 3)

CAUTION:

Use the speed change switch only after the machine

comes to a complete stop.

To change the machine speed, move the speed

change switch to the ‘‘L’’ position for low speed or the

‘‘H’’ position for high speed.

High speed: ordinary wood, plys or plastics

Low speed: metals (steel pipe, sheet metal, stainless

or copper)

Switch action (For JR3000) (Fig. 4)

CAUTION:

Before plugging the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

JR3000 (Eng) (’96. 3. 22)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JR3000 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info