Bedienungsanleitung Makita KP312 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599021

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting depth of cut (Fig. 1)

The depth of cut can be adjusted within a range of 0 –

3.5 mm. Turn the knob on the front of the tool until the

pointer is aligned with the desired cutting depth on the

scale. Set the depth of a cut observing the maximum

depth which is limited by width according to the following

table.

Correlation of width of cut and maximum depth of

cut

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

"OFF" position when released.

For tool with lock button

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

For tool with lock-off button

To prevent the trigger from being accidentally pulled, a

lock-off button is provided. To start the tool, press the

lock-off button and pull the trigger. Release the trigger to

stop.

Overload protector (Option)

This tool is equipped with an overload protector which

automatically cuts out to break the circuit whenever

heavy work is prolonged. When it cuts out, inspect the

blade for damage or something wrong. After making sure

that there is nothing wrong with the tool, push the restart

button to resume operation.

Edge fence (Guide rule) (Fig. 3)

Edge fence is useful for minimizing a short run of cut by

cutting in a uniform width. The edge fence (guide rule) is

provided on the side of the tool. Press two pins for the

edge fence (guide rule) so that the edge fence appears.

Move the tool forward while keeping the flat surface of

the edge fence in contact with the side of the workpiece.

To return the edge fence to an original position, push it

upwards from its underside.

Foot (Fig. 4)

After a cutting operation, raise the back side of the tool

and a foot comes under the level of the rear base. This

prevents the tool blades to be damaged.

Guideline of cutting blade passage (Fig. 5)

Both ends of the front base are a guideline to show the

ends of cutting blades passage.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing planer blades (Fig. 6)

CAUTION:

• Tighten the blade installation bolts carefully when

attaching the blades to the tool. A loose installation bolt

can be dangerous. Always check to see they are tight-

ened securely.

• Handle the blades very carefully. Use gloves or rags to

protect your fingers or hands when removing or install-

ing the blades.

• Use only the Makita wrench provided to remove or

install the blades. Failure to do so may result in over-

tightening or insufficient tightening of the installation

bolts. This could cause an injury.

To remove planer blades on the drum, loosen the eight

installation bolts by only one full turn with the hex

wrench.

Then push and slide a planer blade sideways from the

belt side using the helm of the hex wrench.

To remove another planer blade, follow the same proce-

dure as above. (Fig. 7 & 8)

To install the blades, first clean out all chips or foreign

matter adhering to the drum or blades.

Insert the blade between the drum and the set plate from

the nozzle extraction side so that the blade will be cen-

tered from both ends of the drum or set plate.

First tighten the eight installation bolts lightly and evenly

shifting from the center bolts to the outward bolts with the

hex wrench.

And then, tighten all of the installation bolts securely.

Install another blade in the same manner as above.

(Fig. 9)

Width of cut Maximum depth of cut

0 – 150 mm 3.5 mm

150 – 240 mm 2 mm

240 – 312 mm 1.5 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita KP312 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info