Bedienungsanleitung Makita MT450 (Seite 5 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598762

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Adjusting the shoe (Fig. 1 & 2)

When the blade loses its cutting efficiency in one place

along its cutting edge, reposition the shoe to utilize a

sharp, unused portion of its cutting edge. This will help to

lengthen the life of the blade. To reposition the shoe, push

the shoe button in the “A” direction with a click and

reposition as shown in the figure which allows you to

make five-way adjustment. To secure the shoe, push the

shoe button in the “B” direction with a click.

Switch action

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• Switch can be locked in “ON” position for ease of

operator comfort during extended use. Apply caution

when locking tool in “ON” position and maintain firm

grasp on tool. (Fig. 3)

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

For continuous operation, pull the switch trigger, push in

the lock button and then release the switch trigger.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing the saw blade for

Model MT450T

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury. (Fig. 4)

To install the saw blade, always make sure that the blade

clamp lever is in released position on the insulation

cover before inserting the saw blade. If the blade clamp

lever is in fixed position, rotate the blade clamp lever in

the direction of the arrow so that it can be locked at the

released position .

CAUTION:

• If you do not insert the saw blade deep enough, the

saw blade may be ejected unexpectedly during

operation. This can be extremely dangerous.

• Keep hands and fingers away from the lever during the

switching operation. Failure to do so may cause

personal injuries. (Fig. 5)

Insert the saw blade into the blade clamp as far as it will

go. The blade clamp lever rotates and the saw blade is

fixed. Make sure that the saw blade cannot be extracted

even though you try to pull it out. (Fig. 6)

To remove the saw blade, rotate the blade clamp lever in

the direction of the arrow fully. The saw blade is removed

and the blade clamp lever is fixed at the released

position .

NOTE:

• If you remove the saw blade without rotating the blade

clamp lever fully, the lever may not be locked in the

released position . In this case, rotate the blade

clamp lever fully again, then make sure that the blade

clamp lever locked at the released position .

• If the lever is positioned inside the tool, switch on the

tool just a second to let the blade clamp out. Switch off

and unplug the tool from the mains before working on

the blade clamp lever.

Installing or removing the saw blade for

Model MT450

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury. (Fig. 7)

To install the blade, loosen the screw on the blade clamp

with the hex wrench. Insert the blade between the blade

clamp and the slider so that the pin on the slider fits into

the hole in the blade shank. If the pin cannot easily fit into

the hole, remove the hex wrench from the screw and then

try again.

CAUTION:

• If you tighten the screw without the pin on the slider

fitting properly in the hole in the blade shank, the pin or

the blade shank will be damaged. This may cause the

blade to be extracted unexpectedly during operation.

(Fig. 8)

After the pin fits properly into the hole, tighten the screw

clockwise securely. Make sure that the blade cannot be

extracted even though you try to pull it out.

To remove the blade, follow the installation procedure in

reverse.

Hex wrench storage (Fig. 9)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

CAUTION:

• Always hold the tool firmly with one hand on insulation

cover and the other on the switch handle.

• Always press the shoe firmly against the workpiece

during operation. If the shoe is removed or held away

from the workpiece during operation, strong vibration

and/or twisting will be produced, causing the blade to

snap dangerously.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita MT450 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info