Bedienungsanleitung Makita sa 7000 c (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

391187

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

Explanation of general view

1 Shaft lock

2 Lock button

3 Switch trigger

4 Speed adjusting dial

5 Lock nut

6 Abrasive disc

7 Rubber pad

8 Lock nut wrench

9 Exhaust vent

10 Inhalation vent

11 Commutator

12 Insulating tip

13 Carbon brush

14 Screwdriver

15 Brush holder cap

SPECIFICATIONS

Model SA7000C

Disc diameter ...................................................... 180 mm

Spindle thread ........................................................... M14

Rated speed (n) / No load speed (n

o).......0 – 4,000 min

-1

Overall length ...................................................... 453 mm

Net weight .............................................................. 3.4 kg

Safety class............................................................. /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use

The tool is intended for the sanding of large surface of

wood, plastic and metal materials as well as painted sur-

faces.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

SPECIFIC SAFETY RULES

GEB036-2

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to sander safety rules. If you use this tool unsafely or

incorrectly, you can suffer serious personal injury.

Safety Warnings Common for Sanding Operation:

1. This power tool is intended to function as a

sander. Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

serious injury.

2. Operations such as grinding, wire brushing, pol-

ishing or cutting-off are not recommended to be

performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. The arbour size of backing pads or any other

accessory must properly fit the spindle of the

power tool. Accessories with arbour holes that do

not match the mounting hardware of the power tool

will run out of balance, vibrate excessively and may

cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as backing pad

for cracks, tear or excess wear. If power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After inspect-

ing and installing an accessory, position your-

self and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute. Dam-

aged accessories will normally break apart during

this test time.

8. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small workpiece frag-

ments. The eye protection must be capable of stop-

ping flying debris generated by various operations.

The dust mask or respirator must be capable of fil-

trating particles generated by your operation. Pro-

longed exposure to high intensity noise may cause

hearing loss.

9. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of opera-

tion.

10. Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or

its own cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power

tool “live” and shock the operator.

11. Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

12. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita sa 7000 c Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita sa 7000 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info