Bedienungsanleitung Makita UB 140D (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448666

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well venti-

lated area during charging.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB032-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Always use protective goggles, a cap and mask

when using the blower.

3. Never point the nozzle at anyone in the vicinity

when using the blower.

4. Always use the dust bag when collecting dust,

chips and the like.

5. Do not collect still smoldering cigarette ashes,

freshly cut metals shavings, screws, nails and

the like.

6. Never block suction inlet and/or blower outlet.

Increased motor revolution may cause danger-

ous fan breakage.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the push buttons on both sides of

the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Charging (Fig. 2)

Plug the battery charger into the proper A/C voltage source. The charging light will flash in green color. Insert the bat-

tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective

markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When

the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The

charging light will remain lit steadily during charging. When the charging light color changes from red to green, the

charging cycle is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the

charger will switch into its “trickle charge (maintenance charge)” mode which will last approximately 24 hours. After

charging, unplug the charger from the power source. Refer to the table below for the charging time.

CAUTION:

• The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufac-

turer’s batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location

exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a

while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the

battery cartridge from the battery charger.

• If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The ter-

minals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will

switch into its “trickle charge (maintenance charge)” mode and keep the battery cartridge fresh and fully charged.

Battery type Capacity (mAh) Number of cells Charging time

1222 2,000 10 Approx. 45 min.

1233 2,200 10 Approx. 50 min.

1234 2,600 10 Approx. 60 min.

1235 3,000 10 Approx. 70 min.

1422 2,000 12 Approx. 45 min.

1433 2,200 12 Approx. 50 min.

1434 2,600 12 Approx. 60 min.

1435 3,000 12 Approx. 70 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita UB 140D Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita UB 140D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info