600703
11
Zoom out
Zoom in
Vorherige Seite
1/30
Nächste Seite
11
NOTICE:
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Inspecting blades
Check the blades daily for damage, crack and dull edge.
Ask Makita authorized service center to replace damaged
blades or sharpen dull blades.
Adjusting the blade clearance (Fig. 17 &
18)
The upper/lower blades wear out gradually after
operations. If you cannot get a clean cut though the
blades are sharp enough, adjust the clearance as follows.
The tightness of the truss bolt decides the clearance of
the blades.
The nut holds the truss bolt with certain tightness. Too
loose clearance causes blunt cut, but too tight clearance
causes unnecessary heat and sooner worn-out of the
blades.
1. Loosen the nuts with a wrench.
2. Tighten the bolts lightly till they stop. And then, screw
them back a quarter to half turn each to gain
necessary clearance.
3. Hold the bolts and tighten the nuts.
4. Apply light oil on the friction surface of the blades.
5. Switch on the tool and pull the switch trigger.
6. Measure the time necessary for the blades to stop
after releasing the switch trigger. If it is two seconds or
longer, switch off the tool and repeat the step 1 to 6.
7. Switch off the tool and remove the battery cartridge,
and touch the blade surface. If they are not too hot to
touch, you have made a proper adjustment. If they are
too hot to touch, turn the bolts back a little and repeat
the step 5 to 7.
Lubricating moving parts
NOTICE:
Follow the instruction of the frequency and amount of
grease supplied. Otherwise insufficient lubrication may
damage moving parts. (Fig. 19)
Lubricate gears in the cutter unit every 25 working hours.
The grease hole locates under the bolt. Remove the bolt
to lubricate.
Add approx. 3 g (4 cc) of grease to the point A of the
gearbox and 5 g (7 cc) of the grease to the point B
respectively via the grease holes. Return the bolt after
lubrication.
After filling correct amount of grease, grease will come out
a bit from the base of the blade during the first operation.
Overall inspection
CAUTION:
Check for damaged parts and blades. Ask Makita
authorized service center to replace them if necessary.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita UN490D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info