Bedienungsanleitung Maktec DC1251 (Seite 3 von 16) (Alle Sprachen)

600579

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

CAUTION:

1. SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for battery charger.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) prod-

uct using battery.

3. CAUTION – To reduce risk of injury, charge only MAKITA TYPE rechargeable batteries. Other types of batteries may burst

causing personal injury and damage.

4. Non-rechargeable batteries cannot be charged with this battery charger.

5. Use a power source with the voltage specified on the nameplate of the charger.

6. Do not charge the battery cartridge in presence of flammable liquids or gases.

7. Do not expose charger to rain or snow.

8. Never carry charger by cord or yank it to disconnect from receptacle.

9. After charging or before attempting any maintenance or cleaning, unplug the charger from the power source. Pull by plug

rather than cord whenever disconnecting charger.

10. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

11. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in

order to avoid a hazard.

12. Do not operate or disassemble charger if it has received a sharp blow, been dropped, or otherwise damaged in any way;

take it to a qualified serviceman. Incorrect use or reassembly may result in a risk of electric shock or fire.

13. The battery charger is not intended for use by young children or infirm persons without supervision.

14. Young children should be supervised to ensure that they do not play with the battery charger.

15. Do not charge battery cartridge when temperature is BELOW 10°C (50°F) or ABOVE 40°C (104°F).

16. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

17. Do not allow anything to cover or clog the charger vents.

Charging

1. Plug the battery charger into the proper AC voltage source.

2. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their

respective markings on the charger.

3. When the battery cartridge is inserted fully, the charging light color will flash in red color and charging will begin.

4. When charging is completed, the charging light goes out.

5. After charging, unplug the charger from the power source.

Refer to the table for the charging time below.

(Note) *1...7.2 V battery can be charged with the charger DC1251 only.

*2...14.4 V and 18 V batteries can be charged with the charger DC1850 only.

NOTE:

• The battery charger is for charging Makita TYPE battery cartridge. Never use it for other purposes or for other manufacturer’s

batteries.

• When you charge a battery cartridge which is new or has not been used for a long period of time, it may not accept a full

charge until after discharging it completely and recharging a couple of times.

• When you charge a battery cartridge from a just operated tool or a battery cartridge which has been left in a location exposed

to direct sunlight or heat for a long time, let it cool off. Then re-insert it and try to charge it once more.

• When you charge a battery cartridge which has not been used for a long period, sometimes the charging light will go out

soon. If this occurs, remove the battery cartridge and re-insert it. If the charging light goes out within one minute even after

repeating this procedure a couple of times, the battery cartridge is dead. Replace it with a new one.

• The charging time can become longer due to a battery and temperature.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by a Makita

Authorized Service Centers, always using Makita replacement parts.

EC-DECLARATION OF CONFORMITY

ENH005-1

We declare under our sole responsibility that this product is in

compliance with the following standards of standardized doc-

uments, EN60335, EN55014, EN61000 in accordance with

Council Directives, 73/23/EEC and 89/336/EEC.

Yasuhiko Kanzaki

CE 2003

Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes,

Bucks MK15 8JD, ENGLAND

Voltage 7.2 V*1 9.6 V 12 V 14.4 V*2 18 V*2

Capacity

(Ah)

Charging time

(Minutes)

Number of cells 6 8 10 12 15

Ni-Cd

Battery cartridge

7050 9050 1250 1450 1850 1.3 60

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Maktec DC1251 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info