636202
5
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
EN
Circuit Card ZM-SKS B / Rev.A 1.3 – 5
5.4 Overview of DIP switch functions
DIP switch Setting Function Connection
DIP 1 ON - Evaluation for 8.2 KOhm closing edge safety device
- Evaluation for pneumatic closing edge safety devices,
in connection with an 8.2 KOhm resistance
Terminal block X3,
Terminals 7 + 8
OFF Evaluation for OPTO closing edge safety device. Terminal block X3,
Terminals 7 + 8 + 9
DIP 2 ON - Pressure switch testing is switched on.
- Pressure switch testing is carried out with the door at the CLOSED end positi-
on. For this, the pressure switch contact must be broken for a moment as the
door touches the ground.
-
OFF - Pressure switch testing is not switched on.
- The pressure switch is not tested at the CLOSED end position.
-
DIP 3 ON - Automatic closing timer is switched on.
- From the OPEN end position, the door closes automatically after the program-
med door-open duration expires.
Basic functions when automatic closing timer is switched on
- If the photocell barrier is interrupted during closing, the door stops and then
opens again. The door open duration starts anew.
- If the photocell barrier is interrupted during the door open duration, the door
open duration starts anew.
- If the closing edge safety system is activated during closing, the door stops
and then opens again. The door open duration starts anew.
If the closing edge safety device is activated three times during one cycle, the
door does not close automatically again.
-
OFF - Automatic closing timer is switched off. -
DIP 4 ON - Yard light function is switched on when the OPEN command is given.
- With the yard light setting, the light then stays on for 2 minutes. Via DIP
switch 5 it can be set to delay, which means that the drive does not start until
the light has been on for 3 seconds.
Potential-free
switching contact K3,
terminal block X9,
terminals 1 + 2 for connecting
an external light source.
OFF - Red trafc light function is switched on.
- 2 options are available using DIP 5.
Potential-free
switching contact K3,
terminal block X9,
terminals 1 + 2 for connecting a
red trafc light.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marantec AS 210 B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Marantec AS 210 B

Marantec AS 210 B Zusatzinformation - Deutsch - 8 seiten

Marantec AS 210 B Bedienungsanleitung - Deutsch - 12 seiten

Marantec AS 210 B Bedienungsanleitung - Englisch - 12 seiten

Marantec AS 210 B Zusatzinformation - Holländisch - 8 seiten

Marantec AS 210 B Bedienungsanleitung - Holländisch - 12 seiten

Marantec AS 210 B Zusatzinformation - Französisch - 8 seiten

Marantec AS 210 B Bedienungsanleitung - Französisch - 12 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info