Bedienungsanleitung Marantz PM14 MK2 (Seite 5 von 14) (Englisch)

522817

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

NAME AND FUNCTION OF EACH PART

(Figure 1)

A PHONE INPUT jacks

Connect the output jacks of a turntable to these jacks.

B CD PLAYER INPUT jacks

Connect the output jacks of a Compact Disc player to these jacks.

C LINE 1 – LINE 3 INPUT jacks

These are LINE 1 – LINE 3 input jacks which can be used to connect

the audio outputs of AV components such as TV multiplex/stereo audio

turners, VCRs, and leaserdisc players.

D TAPE 1/TAPE 2 IN/OUT jacks

Connect the play (output) jacks and record (input) jacks of tape decks

to these jacks.

Up to these tape decks can be connected.

NOTE:

When a surround processor or graphic equalizer is used, it must be

connected to the TAPE 1 jacks.

E MM/MC SELECTOR switch

When the INPUT SELECTOR is set to PHONE, the type of cartridge

used on the turntable can be selected between MM (Moving Magnet)

and MC (Moving Coil) using this switch.

Set this switch according to the cartridge used on the turntable.

MC is selected when the switch is set to the low position.

F GND (GROUND) terminal

Connect the grounding wire from the turntable to this terminal.

G SPEAKER SYSTEMS

Connect your speaker system to these terminals.

H PRE-OUTPUT terminal

Output jack for connection to extension power-amp, mixer or similar.

q Input Selector Switch (INPUT SELECTOR)

This switch is used to select the program source (PHONO, CD, LINE 1,

LINE 2, LINE 3, TAPE 1, or TAPE 2) to be recorded or played.

w CD Selector Switch (CD SELECTOR)

When the input selector switch q is set to CD, this switch selects the

program sources connected to CD UNBALANCED and CD BALANCED

on the rear panel.

When the switch is not pushed ( ), CD UNBALANCED is selected.

When the switch is pushed ( ), CD BALANCED is selected.

e Warm-up Meter

This meter is used to check the device’s warm-up condition.

The full sound quality of audio equipment can not be obtained immedi-

ately after the power supply is turned on. It is necessary to sufficiently

warm-up the device so that it can exhibit its full potential. After turning

the power supply on, as time passes the temperature of each part of

the device will become the same. At the same time, the electrolytic

condenser is also activated.

Shortly after the power supply is turned on, the meter needle rises, and

reaches approximately 2/3 of the meter range after approximately 30

minutes. At this stage, the warming-up is almost completed, and you

can enjoy listening to music with the full acoustic quality of the device.

The position of the meter needle immediately after the power supply is

turned on and during the warming-up, and the amount of time neces-

sary for the warming-up differ depending on the room temperature and

ventilation of the room in which the device is used.

r Volume Control Knob (VOLUME)

This knob adjusts the volume. Turning the knob to the right ( ), in-

creases the volume. The volume can also be turned up or down with

the remote control unit.

t Balance Control Knob (BALANCE)

This knob is used to correct the imbalance in sound which occurs in

some sources such as stereo broadcasts etc, and to change the output

level of the left or right channel. Note that, if the BALANCE knob is set

fully to the left or right, the sound will not be output of the speaker of the

opposite side.

y Source Direct Switch (SOURCE DIRECT)

Pressing this switch causes the signal to be transmitted without pass-

ing through the balance and tone control circuitry, enabling you to fur-

ther enjoy high-grade sound.

(The sound can not be adjusted with the BALANCE, BASS and TREBLE

knobs.)

u Tone Control Knobs (TREBLE, BASS)

These knobs adjust the high and low frequency ranges. The strength of

each frequency range is controlled by turning the knobs. Each frequency

is boosted by turning the knob clockwise “+“ and reduced by turning it

counterclockwise “–”.

TREBLE： Adjusts the tone of the high frequency range.

BASS： Adjusts the tone of the low frequency range.

i Power Supply Switch (POWER)

Pressing this switch turns the power on and pressing it again turns the

power off.

The light of the warm-up meter lights when the power is turned on. The

light goes out when the power is turned off.

o Headphone Jack (PHONES)

A standard stereo headphone plug can be used in this jack.

!0 Speaker Switch (SPEAKERS)

This switch selects the speaker system.

The SYSTEM A terminal and SYSTEM B terminal are always connected.

Turn the switch off when only using the headphones.

!1 IR sensor window

This is the window which receives the infrared remote control signals.

Point the remote control towards this window and correctly send the

signals.

!2 Record Selector Switch (REC SELECTOR)

This switch is used to select whether the recording is done between the

tape decks with the COPY function or with a signal output to the REC

OUT terminal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz PM14 MK2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info