Bedienungsanleitung Marantz PM6010 OSE (Seite 1 von 10) (Englisch)

522813

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

English

FOREWORD

This section must be read before any connection is made to the mains

supply.

WARNINGS

Do not expose the equipment to rain or moisture.

Do not remove the cover from the equipment.

Do not push anything inside the equipment through the ventilation

holes.

Do not handle the mains lead with wet hands.

EQUIPMENT MAINS WORKING SETTING

Your Marantz product has been prepared to comply with the household

power and safety requirements that exist in your area.

"/N" Version product can be powered by 230 V AC only.

"/T" Version product can be powered by 230 V AC only.

This is a voltage selector (2-position or 4-position) on the rear panel of

the "/K"Version product ,.Be sure to set the voltage selector to the mains

voltage of your area before using the unit.

IMPORTANT:

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved

type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off

and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug

without a fuse is used, the fuse at the distribution board should not be

greater than 5A.

NOTE:

The severed plug must be destroyed to avoid a possible shock hazard

should it be inserted into a 13A socket elsewhere.

HOW TO CONNECT A PLUG

The wires in the mains lead are coloured in accordance with the following

code:

BLUE-"NEUTRAL" ("N")

BROWN-"LIVE" ("L")

1. The BLUE wire must be connected to the terminal which is marked

with the letter "N" or coloured BLACK.

2. The BROWN wire must be connected to the terminal which is marked

with the letter "L" or coloured RED.

3. Do not connect either wires to the earth terminal in the plug which is

marked by the letter "E" or by the safety earth symbol

or coloured

green or green-and-yellow.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead - not simply over the two wires.

Recording and playback of any material may require consent. For further

information refer to the following:

— Copyright Act 1956

— Dramatic and Musical Performers Act 1958

— Performers Protection Acts 1963 and 1972

— any subsequent statutory enactments and orders

ABOUT THIS USER GUIDE

Refer to the Figures on the pages at the rear of this user guide. The call

out numbers on the Figures correspond to those found in the text. All

references to the connections and controls that are printed in BOLD type

are as they appear on the unit.

PRECAUTIONS

The following precautions should be taken when operating the equip-

ment.

GENERAL PRECAUTIONS

When setting the equipment ensure that:

— the ventilation holes are not covered

— air is allowed to circulate freely around the equipment

— it is on a vibration free surface

— it will not be exposed to interference from an external source

— it will not be exposed to excessive heat, cold, moisture or dust

— it will not be exposed to direct sunlight

— it will not be exposed to electrostatic discharges

In addition, never place heavy objects on the equipment.

If a foreign body or water does enter the equipment, contact your nearest

dealer or service center.

Do not pull out the plug by pulling on the mains lead, hold the plug.

It is advisable when leaving the house, or during a thunderstorm, to

disconnect the equipment from the mains supply.

CONNECTIONS

(Figure 1)

CONNECTION OF TUNER

Connect the output jacks of your stereo tuner to the TUNER jacks of this

unit.

CONNECTION OF COMPACT DISC PLAYER

Connect the output jacks of your CD player to the CD jacks of this unit.

CONNECTION OF TURNTABLE

Connect the L (Left) output cord of the turntable to the "L" PHONO jack

of this unit, and connect the R (Right) output cord to the "R" PHONO jack.

Also be sure to connect the turntable's grounding wire to the GND jack

of this unit. The GND jack does not have to be connected if the turntable

is not provided with a grounding wire.

CONNECTION OF TAPE DECK

Connect the IN (recording input) jacks of the tape deck to the OUT jacks

of this unit, and connect the OUT (playback output) jacks of the tape

deck to the IN jacks of this unit.

CONNECTION OF SPEAKER SYSTEMS

This unit is equipped with a sets of SPEAKER SYSTEM terminals.

• The speakers in the speaker system should have an impedance

between 8 and 16 ohms. If speakers with an impedance of less than

8 ohms are connected, the protection circuitry may be activated

during play.

• Connect the Right channel speaker to the R terminals, and the Left

channel speaker to the L terminals.

• The output terminals have positive (r: Red) and negative (s: Black)

polarity, and each speaker also has the same polarity (r and s). When

connecting the speaker, be sure to connect the terminals with the

same polarity (r with r, s with s).

NOTE:

Turn the knobs on the speaker terminals by hand. (Do not use a tool

to turn the knobs.)

CONTROLS, CONNECTORS, AND INDICATORS

(Figure 2)

AUX INPUT JACKS

These are auxiliary input jacks which can be used to connect the audio

outputs of AV components such as TV multiplex/stereo audio tuners,

VCRs, and laserdisc players.

TUNER INPUT JACKS

Connect the output jacks of the tuner to these jacks.

CD PLAYER INPUT JACKS

Connect the output jacks of a Compact Disc player to these jacks.

PHONO INPUT JACKS

Connect the output jacks of a turntable to these jacks.

Marantz PM6010 OSE Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info