Bedienungsanleitung Marmitek SVX10 (Seite 3 von 4) (Englisch, Holländisch)

494338

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Always switch off the power supply before

commencing installation.

• The signal repeater must always be mounted in a junction box

or distribution box at a location of the installation were a

repeated signal is useful. The signal repeater must be

protected by a 16 A automatic fuse or fuse link.

• Connect the phase and neutral wire to the terminals on the

signal repeater, see Figure 1.

Mounting / installation Mounting / installation

PROG.

SVX

Figure 1. Installing and connecting the module.

PROG.

SVX

M = max. 0.5 Nm

Max. torque for screw terminals

Programming the options

The SVX10 is ready for use directly after installation without

programming the module. The default setting for the SVX10 is to

repeat all letter codes. In very specific situations the SVX10 needs

to be programmed to repeat specific letter codes only. To program

the module please follow the procedure as described below.

Program procedure to repeat specific letter codes only:

• Set the SVX10 in programming mode.

• Send the desired letter code, including an arbitrary number

code, twice via a PMIX35, HCB, PUX, or by remote control.

The LED will flash once.

• If necessary program other desired letter codes in the

same way.

• Return the SVX10 to operating mode.

Procedure to reset the SVX10 into the default settings

(repeat all letter codes):

• Set the SVX10 in programming mode.

• Send All Lights On twice. The LED will flash seven times.

• Return the SVX10 to operating mode.

If the LED flashes twice the programmed letter code has already

been programmed. If the LED flashes ten times, this means that

15 letter codes have been programmed.

Programming

Always switch on the power before programming.

Avoid the contact with life parts!

Activating programming mode

The signal repeater needs to be set into programming mode as

follows before it can be programmed:

• Press the program button for at least

three seconds, see Figure 2,

the red LED is now off.

If no setting command is received

within 60 seconds the Module will

automatically exit the

programming mode.

Exit the programming mode

• Briefly press the program

button once, or wait

60 seconds,

and the

programming mode

will automatically be

switched off.

PROG.

SVX

PROG.

Figure 2. Activating and cancelling

programming mode.

Technical data

Marmitek X-10 home automation

Rated voltage 230 Vac, 50 Hz

Current consumption < 1 W

Signal transmission > 5 Vpp in 5 Ω at 120 kHz in accordance with

EN 50065-1, EN 50065-2-1, EN 50065-4-1

Transmission synchronization 1 pulse burst at 0°/180°

Signal sensitivity 25 mVpp…6 Vpp at 120 kHz ± 4 kHz

Signal/noise ratio 1,35 : 1

Connection range Up to 2.5 mm

, tightening torque 0.5 Nm

Minimum ambient temperature 0 °C

Maximum ambient temperature 40 °C (*)

Atmospheric pressure 86 pkA - 106 pkA

Relative humidity

(non condensing) 30 tot 90%

Standards

NEN-EN-IEC 60669-2-1, NEN-EN-IEC 60669-2-2

Marking

(*) Marmitek X-10 modules are suitable for use in homes where the ambient temperature in

the

living area is not higher under normal circumstances than 35°C or may (exceptionally) reach

a maximum of 40°C.

Subject to technical changes without prior notice.

Electrical equipment and systems can be sensitive to signals from

other equipment, which causes electro magnetic disturbance. In

the European Union, countries agreed upon laws for the immunity

(sensitivity) of signals of other equipment as well as equipment

emission (disturbance). When equipment or applications in a certain

surrounding comply with the valid standards, they will not disturb

each other's operations (they are called "Electro Magnetic

Compatible").

For residential surroundings, where the home automation system

Marmitek X-10 is being applied, the European standard for

immunity is standardised in EN 61000-6-1. Equipment that complies

with this standard is resistant to electro magnetic emission of other

equip ment, which complies with the European standard EN 61000-

6-3 for residential surroundings. Experience has shown that in

domestic surroundings, equipment is being used which has an

EMC-emission level that is above the levels stated in EN 61000-6-3.

This equip ment can disturb the correct functioning of the Marmitek

X-10 modules. The immunity of the Marmitek X-10 built-in modules

is therefore revaluated and equivalent to EN 61000-6-2 (the more

severe European standard for immunity in industrial surroundings).

Nevertheless, the application area for Marmitek X-10 will

remain restricted to residential areas.

Undisturbed functioning of Marmitek X-10 automation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek SVX10 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info