Bedienungsanleitung Marshall Code 100 (Seite 5 von 62) (Deutsch, Englisch, Französisch, Spanisch)

705292

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

FRONT PANEL FUNCTIONS (CONT.)

8. MASTER

Controls the overall volume level of your

CODE amplier.

MASTER volume control settings are not

stored as part of a Preset.

9. PRESET

A Preset is a combination of preamp, power

amp & speaker models, with tonal settings

and FX: Chorus, Flanger, Tremolo, Delay

etc, stored to a single location within your

CODE amplier’s memory. This is like a

‘snapshot’ of the whole amplier’s settings

(excluding MASTER), which can be recalled

using the PRESET selector, or with the

optional CODE footcontroller.

Turn the PRESET selector to explore your

CODE amplier’s factory Presets.

10. EDIT

Use the EDIT selector to deep edit a Preset.

Push the EDIT selector to preview the

stored Gain, Bass, Middle, Treble & Volume

settings. Turn the EDIT selector to view the

current Section Switch settings.

To discover how to edit a Preset, go to

‘EDITING A PRESET’ in this manual.

11. F/C

Use this jack socket to connect the

supplied 2-way footswitch for scrolling

through Presets, or to connect the CODE

programable footcontroller (PEDL-91009

sold separately).

12. MP3 PLAYER INPUT

Use this dedicated mini-jack socket to

connect an audio player to practice with or

jam along to music.

13. HEADPHONE OUTPUT

Use this mini-jack socket to connect

headphones for ‘silent’ practice. This can

also be used as a line out.

14. ON/OFF

This is the mains power ON/OFF switch.

SECTION SWITCHES (15 - 21)

The Section Switches represent different ‘sections’ in the guitar signal chain. This is the

route that a guitar signal travels through a conventional amplier setup from the guitar to

the loud speaker(s).

POWER AMP

CABINET

PREAMP

ENGLISH

Marshall

STOMPBOX

MOD

DELAY

REVERB

1718

Marshall

STOMPBOX

MOD

DELAY

REVERB

1718

Pressing the Section Switches (#15 – #21 in

this manual) will activate (Red LED on) and

bypass (LED off) that Section.

FRONT PANEL FUNCTIONS (CONT.)

15. PRE FX

This is where you will nd FX that would typically plug into a conventional amplier setup

between the guitar and the amplier’s input. These FX would typically be in pedal form,

and also known as ‘stompboxes’. The ‘stompbox’ FX in the PRE FX section are:

Compressor

Compressor affects an audio signal’s dynamic range. CODE’s compressor decreases,

or ‘compresses’, any part of your guitar sound that peaks above a certain threshold.

Any part of your guitar sound that remains below the threshold is unaffected.

Compressor can add clarity and consistency to your guitar sound whether clean or

overdriven. Compressor’s editable parameters are:

‘STOMPBOX’ FX

A:>>|<<

ENGLISH

PARAMETER VALUE RANGE DESCRIPTION

Tone 0 - 10 Adjusts the Compressor’s higher and lower

frequencies.

Ratio 0 - 10 Controls how much Compression is applied to a signal

above the threshold.

Compression 0 - 10 Adjusts the point at which Compression is applied to

the signal.

Level 0 - 10 Controls the overall volume level of the Compressor.

Distortion

CODE’s stompbox Distortion’s three Modes simulate solid-state Distortion and

Overdrive FX pedals. GUV Mode is a Marshall Guv’nor™ with Drive and Tone

controls. ODR & DIS Modes provide avours of classic overdrive and distortion

stompboxes. Stompbox Distortion is particularly effective when used with classic

and vintage MST preamp models to provide more drive and sustain. Distortion’s

editable parameters are:

PARAMETER VALUE RANGE DESCRIPTION

Mode GUV, ODR & DIS Marshall Guv’nor, Classic OD pedal

& Classic Distortion pedal.

Drive 0 - 10 Controls the amount of Overdrive or Distortion

applied to the signal.

Tone 0 - 10 Adjusts the amount of upper mid and higher frequency

content in the Overdrive or Distortion before the

signal reaches the amplier panel tone controls.

Level 0 - 10 Controls Distortion’s overall volume level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall Code 100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info