Bedienungsanleitung Marshall JVM215C Combos (Seite 8 von 60) (Deutsch, Englisch, Französisch, Spanisch)

705298

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

Channel Section

Pressing a channel button has two functions:

When coming from a different channel it recalls

the last setting in the new selected channel.

When pressing in the same channel it cycles the

modes: GREEN > ORANGE > RED > GREEN...

Each mode remembers the FX, Reverb and

Master settings.

Example: You are in OVERDRIVE ORANGE

with FX + REVERB and you press CLEAN. The

amp switches to the last Clean mode you had

(letʼs assume it was CLEAN GREEN with

REVERB). If you press the OVERDRIVE switch

you go back to OVERDRIVE ORANGE with FX

+ REVERB. This allows bouncing between

channels without losing the settings. If you now

press OVERDRIVE again, you go to

OVERDRIVE RED with whatever FX, MASTER

and REVERB settings you had last time you

were in this mode.

Pressing REVERB (7) switches the reverb ON

and OFF in the current channel.

Pressing FX LOOP (4) switches the parallel FX

loop ON and OFF in the current channel.

Master Section

REVERB Control (7)

Alongside the REVERB switch each channel

has its own reverb control allowing individual

level settings of the effect.

MASTER 1 / MASTER 2 (5)

These are the master volume controls of the

amplifier. They can be assigned individually to

each of the modes as you wish and the master

selection will be stored in each of the modes.

PRESENCE, RESONANCE (6)

These controls are power amplifier controls and

only have effect when playing through a speaker

(not in silent recording). They affect how the

power amplifier reacts to the connected

speakers and how much control the amplifier

has over them.

Increasing the RESONANCE control

emphasises the natural speakerʼs resonance for

an improved bass response. In the same way,

increasing the PRESENCE control emphasises

the speakerʼs high frequencies which will be

heard as an improved high frequency response

which adds presence to the sound.

Presence and Resonance constitute a powerful

power amplifier equaliser, allowing responses

from a ʻ^ʼ shape when they are fully

counterclockwise, which is felt as a mid boost,

to a ʻvʼ shape when they are turned clockwise,

which is felt as a scooped sound. Again, the

effectiveness of these controls is highly

dependant on the kind of connected speakers.

Care has to be taken to avoid over excursion of

the speaker cones in high resonance settings.

FX LOOP (4)

This is a programmable FX loop which features

a MIX control on the rear panel and it is located

after the pre-amp, right before the reverb and

serial loop circuits. Pressing the FX Loop switch

(4) engages this effects loop. Please refer to the

Serial / Parallel Loop description later on in the

handbook for its operation.

FOOTSWITCH / MIDI PROGRAM (3)

This switch has a dual function:

Pressing it once we enter the FOOTSWITCH

PROGRAM mode. It is indicated by a

continuous red light.

Pressing it twice we enter the MIDI PROGRAM

mode. It is indicated by a blinking red light.

Footswitch program and use

The JVM range features a new type of fully

configurable footswitch. Connection to the

amplifier requires a standard mono 1/4" jack to

jack cable. Any guitar lead will work and

practically there should be no limit in its length.

When the front panel FOOTSWITCH / MIDI

PROGRAM switch is off, the footswitch operates

in safe mode and executes the commands the

moment the switch is pressed down.

If you enter the FOOTSWITCH PROGRAM

mode (LED red) you will be able to program the

footswitch but nevertheless the footswitch and

the amplifier will remain fully operational with the

only difference that the commands will be

executed when releasing the footswitches, as

opposed to the normal mode.

Each of the individual footswitches has 2 modes

of operation: preset store and switch store.

In preset store mode, any of the footswitches

can be configured to store the current amplifier

status. The current channel, master, FX and

reverb status will be stored and recalled when

the respective footswitch is pressed.

Front Panel Operation

JVM 2 Ch Owners Manual Book-00089-01 /12/15 inner.qxd:Layout 1 14/12/15 10:08 Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall JVM215C Combos Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info