Bedienungsanleitung Marshall MB60, 150, 450H, 4410, 4210 (Seite 4 von 5) (Englisch)

442807

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

17. TREBLE Control

By adjusting the Treble control you can add or take

away the higher frequencies in your bass tone. By

increasing the amount of treble you will make your

tone brighter, ideal for more percussive playing

styles.

BLEND

(Only on MB450H, MB4210 & MB4410)

You can select a blend of the two channels either

from the front panel or via the supplied footswitch.

18. BLEND Switch & LED

This switch turns the channel mixing on.

19. BLEND Control

By adjusting this control it is possible to blend your

signal between the Modern and Classic channels.

When you do this the LED will be illuminated red.

20. VOLUME Control - Blend

Adjusts the volume of the Blend.

21. VOLUME - Master

(Only on MB450H, MB4210 & MB4410)

Controls the overall volume.

22. CD IN Jack Socket

If you want to jam to your favourite CD, tape or

mp3 player, merely connect the headphone output

of your device here, adjust the player’s volume to

match that of your guitar and ‘hey-presto’- you've

got the perfect ‘play-along’practice system.

23. HEADPHONES Jack Socket

For use when silent practice is the order of the day.

Connection of headphones will automatically shut

down the internal speaker / speaker cabinet.

24. POWER Switch

The power switch turns your amplifier on and off.

The LED next to the ‘Modern / Classic’switch will

light up when your amplifier is turned on and will

not be lit when the amplifier is switched off.

Note: The power amplifier is protected by a

clipping limiter, so even when you play your amp

loud, the sound remains clean.

(panel shown is MB450H)

Rear Panel Features

1 2 3 4 5 6 7

EUROPE ONLY - Note: This equipment has been tested and found to comply with the requirements

of the EMC Directive (Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.

EUROPE ONLY - Note: The Peak Inrush current for the MB450H, MB4210 and MB4410 is 28 amps.

The Peak Inrush current for the MB150 is 30 amps.

The Peak Inrush current for the MB60 is 13 amps.

ENGLISH

MB450H MB4210 MB4410 MB150 MB60

Power (RMS) @ 4 Ohms 300W 300W 300W 150W 60W

Power (RMS) @ 2 Ohms 450W 450W

450W

Pre-amp Valve ECC83 ECC83 ECC83 ECC83 ECC83

Bass Guitar Input Impedance 1MΩ 1MΩ 1MΩ 1MΩ 1MΩ

CD Input Impedance 10kΩ 10kΩ 10kΩ 10kΩ 10kΩ

Emulated Output Level +4dBu +4dBu +4dBu +4dBu +4dBu

Weight 15kg 33kg 51kg 30kg 23kg

Size (mm) W, H, D 630 x 220 x 235 630 x 535 x 280 630 x 720 x 410 580 x 585 x 355 580 x 505 x 325

with extension cabinet

1. MAINS INPUT

Your amp is provided with a detachable mains

(power) lead, which is connected here.

Note: The specific mains input voltage rating that

your amplifier has been built for is shown on the

back panel. Before connecting for the first time,

please ensure that your amplifier is compatible with

your electricity supply. If you have any doubt,

please get advice from a qualified technician.

Your Marshall dealer will help you in this respect.

Please ensure the amplifier is switched off and

unplugged from the mains electricity supply before

being moved.

2. SPEAKER OUT Socket(s)

There is one speaker jack socket on the MB60 and

MB150 (marked ‘INTERNAL4Ω’). This is where the

power amplifier is connected to the internal

loudspeaker. It can be used to drive an external

cabinet of at least 4 Ohms impedance.

There are 2 speaker jack/SPEAKON

combo

sockets on the MB450H, MB4210 and MB4410.

They accept either a standard 1/4" jack or a

SPEAKON

connector and both of them carry the

same signal allowing 2 cabinets to be connected

simultaneously. The minimum load is 2 Ohms.

3. FOOTSWITCH Jack Socket

Connect the supplied footswitch here. This enables

you to change between Modern and Classic

channels. The MB450H, MB4210 & MB4410 have

a twin footswitch which also switches the Blend

feature.

4. PRE/POST Switch

Selects the signal available at the Balanced line

out. When in PRE position the buffered and level

adjusted input signal is present at the DI output.

The signal before the Master potentiometer is

made available at this connector when in POST

position.

5. BALANCED LINE OUT

The Line Out Jack can be used for connection to

recording equipment for direct recording or for

connection to a P.A. system.

6. RETURN Jack Socket

This is where you connect the OUTPUT of the

effects processor you are using in the effects loop.

7. SEND Jack Socket

If you want to use an external effects processor in

your amp’s built-in Series FX effects loop, this is

the jack you connect to the INPUT of the unit you

are using.

Technical Specification

Safe operating levels: The MB450, MB4210 and MB4410 amplifiers are designed to deliver 450W safely into 2ohm loads.

However, impedances lower than 4 ohms together with high signal levels will produce more internal heating which may

trigger the thermal protective muting.

Follow all instructions and heed all warnings

KEEP THESE INSTRUCTIONS !

MB60_150_450 hbk aw 1/3/07 12:05 pm Page 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall MB60, 150, 450H, 4410, 4210 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info