Bedienungsanleitung Marshall Megastack (MG15FXMSDM) (Seite 4 von 7) (Englisch)

442809

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Footcontroller (optional - PEDL-90008)

Footcontroller Factory Settings

Footswitch 1: Wish You Were Clean

Footswitch 2: Mega Rhythm

Footswitch 3: Conjuring Solo

Footswitch 4: Hangar Solo

Programming

The footcontroller can be programmed to store front

panel switches (Switch Store) or complete presets

(Preset Store).

Switch Store

To assign a front panel switch to a footswitch (1),

press and hold the front panel switch and while held

down press the footswitch (1) you wish to assign it to.

The Digital Display (3) will swirl to show that the

footswitch has been assigned. You can then release the

footswitch and front panel switch.

Preset Store

To assign a preset to a footswitch (1), select the

required channel and modify the front panel controls if

required, press and hold the Store switch on the front

panel and while held down, press your chosen

footswitch (1).

The Digital Display (3) will swirl to show that the

footswitch has been assigned. You can then release the

footswitch and Store switch.

Footcontroller Presets are independent of the dedicated

channel presets stored within the amplifier. This allows

you to create a number of presets based on the same

channel/pre-amp setting.

3 2

1. Footswitches

In addition to the factory preset tones, when the optional stompware® footcontroller is plugged into the

amplifier an additional four voices will be "unlocked" from the amplifier memory. These voices were programmed by

Dave Mustaine and Andy Sneap and details of the control settings and voice parameters can be found on page 41.

Each footswitch can be assigned a different stored function.

2. LED Status Panel

This always reflects the current status of the amplifier or tuner details:

CLN & OD: Current Channel

REV: Reverb On/Off

FX: FX Section On / Off

Ext FX: External FX Loop On/Off (MG50FX & MG100FX)

Damp: Damping Mode (MG50FX & MG100FX)

Tap: Tap Tempo speed.

3. Digital Display

This display indicates the various functions of the footcontroller.

ENGLISH

1. Footcontroller Socket

Jack socket for the connection of the optional footcontroller.

2. Loudspeaker Outputs

Connect the two loudspeaker cabinets provided to the

speaker outputs using the speaker leads supplied.

If you would like to use your MG15HFX amplifier head

with another speaker system (such as a full size 4x12"

cabinet), ensure that the amplifier is provided with a

total load equal to or greater than 8 ohms.

Always use a non-screened Marshall approved speaker

lead when connecting an extension cabinet to these

units.

MP3 / Line In

The 3.5mm MP3 / Line In socket (14) allows the

connection of an external audio source e.g. MP3 or CD

player.

Headphones

The 3.5mm Headphones socket (15) allows the

connection of a pair of headphones. When a jack is

inserted into the headphones socket the unit’s speaker

is muted.

Power

The Power switch (16) turns the amplifier on and off. If

current settings have not been stored they will be lost.

Restoring Settings - WARNING ALL AMP &

FOOTCONTROLLER SETTINGS WILL BE LOST

To restore the unit to Dave’s factory settings (see page

40) you must hold the Store switch (12) while powering

on the unit. The Clean/Crunch (3) and OD (5) lights

will light orange. You can then release the Store

switch (12).

Resetting the amplifier will erase all user Channel

presets and all user footcontroller settings, replacing

them with the factory presets.

MG15FXMSDM Features

* EUROPE ONLY - Note:

This equipment has been tested and found to comply with the requirements of the EMC Directive

(Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U.

* EUROPE ONLY - Note:

The Peak Inrush current for the MG15HFX is 2.5 amps.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Follow all instructions and heed all warnings

KEEP THESE INSTRUCTIONS !

MG15FXMSDM Rear Panel

1 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall Megastack (MG15FXMSDM) Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info