Bedienungsanleitung Matrix Endurance Stepper (Seite 4 von 69) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

738328

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

ENGLISH

ELECTRICAL REQUIREMENTS

For your safety and to ensure performance, the ground on this circuit must be

non-looped (isolated). Please refer to NEC article 210-21 and 210-23. Failure to

follow these electrical requirements could void the Matrix limited warranty.

GROUNDING INSTRUCTIONS

DANGER!

The unit must be grounded. If it should malfunction or breakdown, grounding provides

a path of least resistance for electric current to reduce the risk of electric shock.

The unit is equipped with a cord having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances. Improper

connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualiﬁed electrician or serviceman if you are in doubt as to whether the

product is properly grounded. Do not modify the plug provided with the product. If

it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

110 V UNITS

110 V units require the use of a 100-125 V, 60 Hz and a minimum of a 15A circuit, with a

non-looped (isolated) neutral/ground for power. This unit can be daisy-chained together

with up to 4 units per 15A circuit. Matrix daisy-chain cord adapters are sold separately.

220 V UNITS

220 V units require the use of a 216-250 V, 50 Hz and a minimum of a 15A circuit, with a

non-looped (isolated) neutral/ ground for power. This unit can be daisy-chained together

with up to 4 units per 15A circuit. Matrix daisy-chain cord adapters are sold separately.

DIGITAL TV

An additional power adapter is not needed for the add-on TV or consoles with the

integrated digital TV tuner. An RG6 coaxial cable with ‘F-type’ compression ﬁttings will

need to be connected between the video source and each add-on digital TV unit.

POWER REQUIREMENTS

BATTERY CHARGE (LED CONSOLES)

The Stepper saves its battery charge by moving into a shutdown mode whenever STEP FASTER

appears on the display. If the user does not maintain a step rate above 35 steps per minute, then a

30-second shutdown process begins.

When the battery voltage is low, LOW BATTERY appears on the display if the unit is moving into the

shutdown mode. The following situation is the time to recharge the battery:

• If no one has used the unit for an extended period of time, the battery may need recharging.

• The unit continues to function with a low battery; however, user and program information is lost

once the user stops.

If the battery must be recharged, use the optional power adapter charging unit. The charger should

be connected to the Stepper for a minimum of eight hours to ensure a thorough charge. After a

completion of charge, the battery light turns from red into green (see illustration). If LOW BATTERY

still appears on the display after a full charge, the battery could be extinct. Please check with an

authorized service technician for replacing the battery.

CAUTION: The battery stored inside the unit contains hazardous materials to the

environment. Proper disposal of the battery is required by the local law.

FCC REGULATIONS (USA ONLY)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment o and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

a minimum distance of 20 centimeters between the radiator and your body.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Matrix Endurance Stepper Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Matrix Endurance Stepper

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info