168727
13
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
ENG
M O N O - A M P L I F I E R S
DSC1500.1D
FEATURES:
• PROTECTION and POWER LED indicators
• The REMOTE jack enables a dash mount control for the BASS BOOST
• BALANCED INPUT: balanced MINI-DIN signal input
NOTE: DO not use this input with the RCA input at the same time.
• LOW PASS: Variable from 35Hz to 250Hz
• SUBSONIC FILTER: Variable from 15Hz to 35Hz
• PHASE: Variable from 0 to 180
• BASS BOOST: 45Hz bass boost from 0dB to 9dB
• INPUT LEVEL sensitivities are variable from 0.2volts to 6volts
• Each model is capable of 1ohm minimum
3. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack and control the
Bass Boost setting.
4. Mode-Switch:
The „MODE“ switch must be on „MASTER OUTPUT“ position.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than 1ohm.
1. Interconnect cable checklist:
Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source.
IMPORTANT: Do not connect the Left and Right stereo signals
together to achieve a mono signal as this will damage the output
stage of source and possibly the input stage of the amplifier.
- Use at least 1,5 sqmmspeaker wiring. These amplifiers feature dual speaker
terminals, simplifying the hookup of multiple speakers.
STANDARD OPERATION
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
MONO
LINE INPUT
BASS-REMOTE
SUBWOOFER
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
SUBWOOFER
WITH DUAL-
VOICE COIL
4. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack of the „MASTER“ amp
and control the Bass Boost setting of both amps together.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than 2ohm.
Check the below featured connection figures.
1. Interconnect cable checklist MASTER:
Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source into the „MASTER“ amp.
2. Interconnect cable checklist SLAVE:
Connect a mono line cable from „MASTER OUTPUT “ of the „MASTER“ amp
with the „SLAVE INPUT “ of the „SLAVE“ amp.
3. Mode Switch:
The „MODE“ switch of the „MASTER“ amp must be in position „MASTER OUTPUT“.
The switch of the „SLAVE“ amp in position „SLAVE INPUT“.
MASTER/SLAVE OPERATION
Amplifiers can run at a 2 ohm load
minimum when linked.
2 SUBWOOFERS
WITH SINGLE-
VOICE COIL
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
MONO
LINE INPUT
BASS-REMOTE
BRIDGING
JUMPER CABLE
MASTER TO SLAVE
RCA JUMPER
CABLE
INVERT POLARITY
ON VOICE COIL 2
INVERT POLARITY
ON SUBWOOFER 2
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MB Quart dsc1000 1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info