168723
11
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
FEATURES:
• PROTECTION and POWER LED indicators
• Bass EQ: 45Hz bass boost from 0dB to 9dB
• X-OVER:
- LP/BP: Selects built in LOW PASS filter, variable from 30Hz to 150Hz
- HP: Selects built in HIGH PASS filter, variable from 10Hz to 1.2KHz
- FULL: Bypasses all crossovers for full frequency range operation
Note that the LOW PASS signal is MONO
- In the LP position, the HIGH PASS filter acts as a subsonic filter. When the
HP switch is higher adjusted than 150Hz, you can hear no sound
- When the LP mode is selected, a 0 to +9dB at 45Hz BASS EQ is active
• The REMOTE jack enables a dash mount control for the BASS EQ in LP mode only
• INPUT LEVEL sensitivities are variable from 0.2volts to 6volts
• INPUT MODE: In the 2CH mode, all four channels are supplied signal from CH1/2 RCA jacks.
In the 4CH mode, CH1/2 are supplied signal from CH1/2 RCA jacks and CH3/4 are supplied
signal from CH3/4 RCA jacks.
3. Crossover frequency control checklist:
N/A for full range operation.
FULL RANGE
STEREO LINE INPUTS
FULL RANGE
SPEAKERS
1. Interconnect cable checklist:
Connect the 4 inputs of the amplifier to a Radio/CD with quality RCA cables.
2. Crossover switch:
-1/2CH X-OVER: FULL
-3/4CH X-OVER: FULL
4 CHANNEL FULL RANGE STEREO
3. Input Mode:
4CH
4. Line Level, Bass EQ, Low Pass & High Pass:
Refer the section “Setting up systems after installation for best performance.” on
page 2.
5. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack and
control the Bass EQ setting for CH3/4.
6. Speaker Connections:
Connect the subwoofer- to 3CH- and the subwoofer+ to 4CH+ terminal. Connect
the remaining speakers in standard stereo wiring to 1CH and 2CH.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than
4ohms in mono operation and 2 ohms in stereo operation.
This illustration shows how to use your 4 channel amplifier as a 3 channel unit
by taking advantage of the mono bridging capability on all Discus amplifiers.
1. Interconnect cable checklist:
-1/2CH: Connect the inputs of channel pair1/2 to a suitable stereo source with
quality RCA cables.
-3/4CH: Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source.
IMPORTANT: Do not connect the Left and Right stereo signals
together to achieve a mono signal as this will damage the output
stage of source and possibly the input stage of the amplifier.
2. Crossover switch:
-CH1/2 X-OVER: FULL
-CH3/4 X-OVER: LP
3 CHANNEL OPERATION
MONO LINE INPUT
VIA Y-ADAPTER
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
MONO SUBWOOFER
ENG
FULL RANGE
STEREO LINE INPUT
4 - C H A N N E L - A M P L I F I E R S
DSC480/DSC4125
• Each model is capable of 4ohms or 2ohms operation per channel, or 4ohms mono
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MB Quart dsc4125 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info