Bedienungsanleitung Meliconi universal 4 (Seite 2 von 6) (Englisch)

122407

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

SET-UP

Read these instructions

carefully before programming

your remote control!

MAKE SEARCH PROGRAMMING MODE

1.Turn ON the appliance:

– if a VCR, insert a cassette

– if SAT, select a program

– if DVD, insert a DVD.

2. In the code book enclosed, look for the

make of your appliance and make a

note of the code indicated at the side

(e.g. Philips 001) or the code for the

make indicated by the arrow.

3.Press and release the TV - VCR - SAT -

DVD selection button for the appliance

you want to use:

– the TV button is used to search only

for the TVs of the make selected

– the VCR button is used to search only

for the VCRs of the make selected

– the SAT button is used to search only

for the SATs of the make selected

– the DVD button is used to search only

for the DVDs of the make selected.

4. Hold down the SHIFT and ON/OFF

buttons together until the TV - VCR -

SAT - DVD selection buttons

start to flash indicating that the

remote control is programming.

5. Release the buttons. Within 15

seconds, enter the make code

previously identified (e.g. 001).

The TV- VCR - SAT -DVD selection

button flashes more quickly to indicate

that the remote control is ready for the

search.

6. Point the remote control at the

appliance. Press and release one of

the most frequently used keys several

times STOPPING when the appliance

responds correctly to the command.

7. When the appliance responds

correctly, press SHIFT to confirm.

Three flashes indicate that the

operation has been completed

correctly.

Identify and make a note of the code

for the appliance which you have

searched for following the code

noting procedure (see “NOTING THE

PROGRAMMED CODE” section).

Warning: program one appliance at a time.

SHIFT

FITTING THE BATTERIES

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new AAA/LR03 alkaline batteries.

Insert the batteries as shown.

• The batteries must be changed once a year.

• If the TV - VCR - SAT - DVD/ selection buttons start

to flash during use, this indicates that the batteries

are low and should be changed.

• When you remove the batteries, fit the new ones

within 5 minutes or you may have to reprogram your

remote control.

• Make a note of the codes for the TV - VCR - SAT -

DVD equipment on the adhesive label inside the

battery cover. This note will be handy if you have to

reprogram your control.

DVD

SAT

VCR

NOTE: THE SELECTION BUTTON

STOPS FLASHING.

The remote control leaves the

programming mode and the

TV - VCR - SAT - DVD selection

button stops flashing:

•

if no buttons are pressed for 15 seconds

•

if an invalid make code is entered

•

if the code search list is completed. In

this case, go back to point 3 or switch to

programming mode C

•

if you press the TV - VCR - SAT - DVD -

F1 - F2 - F3 - F4 buttons by mistake.

To program the Universal 4 remote

control, follow the indications

in section A , B or C .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meliconi universal 4 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info