Bedienungsanleitung Meridian DVP 1080 HD (Seite 29 von 34) (Englisch)

494961

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Tr o u b l e s h o o t i n g

2 5

Processor setup

I changed the output scanrate, but the processor did not register

the scanrate selection

Changing the output scanrate requires confirmation of the new output scanrate selection.

Do not select an output scanrate which exceeds display device capabilities (refer to display

device User’s Manual).

• Enter the

SETUP MENU by pressing Menu on the IR remote for seven seconds

• Front Panel LCD display will indicate

SET: NTSC SCANRATE and the current

RESOLUTION below

• Press

< or > on the IR remote to select the appropriate output scanrate

• Press

Store on the IR remote

• Front Panel

LCD display will indicate ARE YOU SURE?

• Press

Store to confirm resolution selection.

Note: Use the same procedure above during SET: PAL SCANRATE, if applicable

(International use)

I selected, SET: NTSC SCANRATE / 1920x1080, now there is no

video output.

The 1920x1080 output scanrate is a Progressive Format (67.43kHz), not a 1080i HDTV

Interlaced Format (33.75kHz). The display device must be capable of receiving this scanrate

(refer to display User’s Manual).

When utilizing the DVI OUTPUT, cable lengths to support 1920x1080p should be no

greater than 16ft (5m). Cable lengths longer than 16ft (5m) may require a DVI to Fibre

Optic connection. DVI cable lengths longer than 16ft (5m) may render an unstable image,

“sparkles” throughout the image, or no image at all.

Note: Some digital displays may have a physical pixel density of 1920x1080, but will not

display the actual 1920x1080p/60Hz signal received by the DVP-1080 processor. Example:

1920x1080, 24p/sF. Think of 24p/sF as an Interlaced signal, whereby, a Progressive HD

Segmented Frame is displayed as two individual frames (similar to 1080i), then spliced back

together; an Interlaced Format.

Is SET: NTSC SCANRATE / 1920x1080 an Interlaced or Progressive

video signal?

The 1920x1080 output scanrate selection is a Progressive Format signal (67.4KHz, 60Hz

refresh). Typically, only high resolution displays will accept/resolve this input signal, such as

9”CRT projection, or a digital display device with a native pixel density of 1920x1080.

Note: Some digital displays will have a physical pixel density of 1920x1080; however, may

not accept this input scanrate. If not, the image may either be split, or half the image is

present, or no image at all. Refer to display user’s manual for signal compatibility.

If the display does not accept 1920x1080 at 60Hz, then you must choose an alternate

resolution the display will understand, such as 1280x720 or 1920x540p (1080i equivalent).

Both output resolutions are perceived by the display as a DTV video signal.

WARNING

DAMAGE may occur if the output scanrate selected within the DVP-1080 SETUP MENU

exceeds theability of the display device to show the image.

My connection to the display device is analogue. Which SET:

ACTIVE OUTPUT format should I choose, RGB or YPrPb?

SET: ACTIVE OUTPUT / ANALOG RGB + DVI and SET: ACTIVE OUTPUT / ANALOG

RGB

When DVI is not available, the preferred analogue output selection from the DVP-1080 is

always RGB, intimating RGBHV. This produces the highest quality analogue signal, as the

processor will have pre-decoded the incoming video signal to its fundamental constituents

of Red, Green, Blue, horizontal sync/vertical sync.

SET: ACTIVE OUTPUT / ANALOG YPrPb

When DVI is not available, and display does not have either an RGBHV or 15-pin (VGA)

input connection, select SET: ACTIVE OUTPUT / ANALOG YPrPb from within the SETUP

MENU.

You must also select either SET: NTSC SCANRATE / 1280x720 or 1920x540 (1080i

equivalent), as these scanrates are the only valid Component video output formats which

the display will understand; both the 1280x720 and 1920x540 scanrates are recognized by

the display device as a DTV video signal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meridian DVP 1080 HD Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info