625666
13
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
ENGLISH
13
ENG
Pull out the mains plug immediately if the battery
charger starts to smoke or flames emerge!
See page 3 (please unfold).
PowerCutter...:
1Enclosure
2Handle
3 Battery pack release
4 Battery pack
5 Trigger switch
6 Switch lock (against accidental activation)
7 Hand protection
8 Hexagon spanner
9 Screw with Belleville spring (for securing
cutting blade)
10 Cutting blades
11 Upper cutting blade
12 Bearing
Battery charger LC 60:
13 C
harging compartment
14 W
arning display
15 O
peration display
Battery charger LC 60:
Automatic balancing of the individual battery
cells permits optimum utilisation of the available
capacity and, at the same time, lengthens the
service life of the battery pack.
PowerCutter...:
Check Quick stop:
Switch machine on briefly and then off again. Have
the machine repaired if braking time is clearly
lengthened.
Charge the battery pack before use (4).
Battery charger LC 60:
Before plugging in, check to see that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Self-test
Insert the mains plug. The warning display (14) and
the operating display (15) light up in succession for
approx. 1 second.
8.1 Battery pack
Removing battery pack:
Press the battery pack release (3) and remove
the battery pack (4).
Inserting battery pack:
Push in battery pack (4) until it engages.
8.2 Switching On and Off
Switching on
(safety operation):
Push the switch lock (6) in the direction of the
arrow and press the trigger switch (5).
To switch off:
Release the actuated trigger switch (5).
Thanks to the patented Quick stop, the cutting
blades come to a standstill within approx. 0.3
seconds.
Have the machine repaired if braking time is
clearly lengthened.
The noise that sometimes occurs during a
machine Quick stop is design-related and has no
influence on operation and service life.
8.3 Replacing cutting blades
Replace cutting blades (10) (or turn then over) if
they are blunt or damaged.
Never check the sharpness of the cutting
blades with your fingers. The cutting blades
are blunt if the cut twigs or leaves are chapped or
frayed.
Remove the battery pack (4) from the
machine to prevent accidental activation.
Danger of injury from the sharp edges of the
blades. Do not touch the cutting blade (10)
and upper cutting blade (11). Wear protective
gloves.
See illustration (A), page 3.
1 Remove battery pack
(4)
.
2 Remove enclosure (1) from cutting blade.
3
Block the cutting blade (10)
with a sufficiently
long wooden rod (or non-ferrous metal rod)
to prevent rotation (do not block or hold
with your fingers or hand).
4 Remove screw with Belleville spring (9)
using a hexagon spanner (8) by turning
counterclockwise (right-hand thread).
5 Remove wooden rod (or non-ferrous metal
rod).
6
Carefully remove the cutting blade (10)
.
Cutting blades (10)
ground on both sides
5Overview
6 Special Product Features
7 Commissioning
8 Use of PowerCutter...
17026903_0409 PowerCutter.book Seite 13 Dienstag, 14. April 2009 1:33 13
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo PowerCutter Li wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info