Bedienungsanleitung Metronic ZAP 6 - 495398 (Seite 3 von 53) (Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

495007

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

FOREWORD

Thank you for choosing a universal METRONIC remote. We are condent you will be fully satised with this product. The

495398 model allows you to control up to 6 appliances: TV, Satellite receiver (SAT), DVD recorder (DVD) or HIFI system (AUX),

DVB-T set top box (TNT), ADSL box (BOX). After inserting the 1.5V AAA batteries (not included) in the remote, you can set

up the remote for each appliance that you wish to control. The universal METRONIC remote has been conceived to control

most products of each brand. This is why you have the choice between 3 types of set ups: by Brand code, automatic search

or through the learning function. In the set up details below, we use a TV as example. In order to set up the remote for your

Satellite receiver or DVB-T set top box, replace ‘TV’ with ‘SAT’ or ‘TNT’. After you have set up the remote, simply press the TV,

SAT, TNT etc key to select the appliance you wish to control.

In case your equipment is not recognized by this model, you may teach him (LEARN) through the original remote.

A - Set up by brand code

1 - Switch on your TV.

2 - Look up in the following pages the codes that correspond to the brand of your TV (i.e. for AEG, you should try the code

0589, then 1423 if the rst code does not work, and nally 0043 if none of the two rst codes work).

3 - Press the PROG and TV keys together for a few seconds until the light switches on. If you wait too long before pressing

another key, the remote will go into standby and the light will switch o. You should then start at Step 3.

4 - Enter one of the 4-digit Brand codes. After each digit, the light will briey switch o. It will switch o for good after you

have entered the 4th digit. If the light blinks twice and then stays on, try the next code.

5 - Point the remote towards your TV and try using the main features (changing channels, adjusting sound…)

6 - If the remote does not control the TV properly, try the set up again (from 3) with the next Brand code. If the remote

controls the TV correctly, then the set up is over. If the remote does not work properly with any code, you should try an

automatic search.

B - Automatic Search

1 - Switch on your TV. The automatic search might take a little while (up to 15 minutes).

2 - Press the

PROG

and TV keys together for a few seconds until the light switches on. When you release the keys the light

should stay on.

3 - Press the

PROG

key. The light should start blinking. Press the key until the light switches o and slowly starts blinking

again. This means the automatic search has started. The light should stay on and blink every time a new code is entered.

You should be ready to press the 0 key.

4 - As soon as the TV switches o, press the 0 key. The light should start blinking. Press the TV key. The light should switch

o. Note: You should be quick enough not to exceed 1 second before the next code from your remote control (a bit less

than 1 second between turning TV o and time to press key «0»).

5 - As your TV is now switched o, switch it on again using the original remote or with the front keys.

6 - Point the remote towards your TV and try using the main features (changing channels, adjusting sound…). If the remote

does not control the TV properly, try the automatic set up again (from 2). If the remote controls the TV correctly, then

the set up is over.

C - Learning function

If the rst two methods have failed, you can still set up the remote through the learning function. The method consists in co-

pying the keys from the original remote onto a key of your choosing on your new universal remote. The learning function can

also be used when Brand code set up and Automatic search only partly function (ineective special functions, for instance).

1 - Place both the original and the 495398 remotes up to a distance of three centimetres away, facing each other.

2 - Press the PROG key and push down. While keeping the PROG key pressed, press TV key, the warning light comes on.

Release both keys, and the light remains lit.

3 - Press the LEARN key, the warning light briey switches o, and comes on again.

4 - Press the key you want to program on your new universal remote 495398 (VOL+ for ex.), the light briey switches o,

and lights up again.

5 - Press the key to copy on the original remote (VOL+ in the ex.), the light blinks twice as soon as the key is recognized. If

the light does not blink, bring both remotes closer and press the key to copy again. If you take too much time to press

on the original key, the light will switch o, and you will have to start again from step 2.

6 - Start again from step 4 with the following keys (VOL -, POWER, 1,2,…).

7 - Once the last key has been recognized, press on LEARN, the light switches o showing that you have left the learning

function.

8 - Point the remote at your TV set and try to press the keys you have just programmed. If the TV set answers badly or does

not answer at all to some keys, start the learning function again for them from step 2. If the remote controls the TV set

correctly, then the set up is over.

Changing batteries

When the remote starts struggling to control the appliances or if it does not work properly, you should try changing

batteries. Thanks to its memory function, you can change batteries withouht losing your settings on the remote.

6 in 1 UNIVERSAL REMOTE CONTROL

Metronic ZAP 6 - 495398 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info