Bedienungsanleitung Microlife BPB1 Classic (Seite 5 von 69) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

773466

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

3BP B1 Classic EN

6. The result, comprising the systolic AT and the diastolic AK blood

pressure and the pulse rate AL is displayed. Note also the

explanations on further display symbols in this booklet.

7. When the device has finished measuring, remove the cuff.

8. Switch off the device. (The monitor does switch off automati-

cally after approx. 1 min.).

You can stop the measurement at any time by pressing the

ON/OFF button (e.g. if you feel uneasy or an unpleasant

pressure sensation).

Manual inflation

In case of high systolic blood pressure (e.g. above 135

mmHg), it can be an advantage to set the pressure individually.

Press the ON/OFF button after the monitor has been pumped up

to a level of approx. 30 mmHg (shown on the display). Keep the

button pressed until the pressure is about 40 mmHg above the

expected systolic value – then release the button.

How not to store a reading

As soon as the reading is displayed press and hold the ON/OFF

button 1 until «M» AO is flashing. Confirm to delete the reading by

pressing the time button 4.

«CL» is displayed when the reading is deleted from the

memory successfully.

How do I evaluate my blood pressure?

The triangle on the left-hand edge of the display AN points at the

range within which the measured blood pressure value lies. The

value is either within the optimum (white), elevated (hatched gray)

or high (black) range. The classification corresponds to the

following ranges defined by international guidelines (ESH, ESC,

JSH). Data in mmHg.

The higher value is the one that determines the evaluation.

Example: a blood pressure value of 140/80 mmHg or a value of

130/90 mmHg indicates «blood pressure too high».

Appearance of the Irregular Heartbeat (IHB) Symbol

This symbol AS indicates that an irregular heartbeat was detected.

In this case, the measured blood pressure may deviate from your

actual blood pressure values. It is recommended to repeat the

measurement.

4. Data Memory

This device automatically stores the last 30 measurement values.

Viewing the stored values

Press the M-button 3 briefly, when the device is switched off. The

display first shows «M» AO and «A», which stands for the average

of all stored values.

Pressing the M-button again displays the previous value. Pressing

the M-button repeatedly enables you to move from one stored

value to another.

Blood pressure readings with suboptimal cuff fit AQ-A are

not considered in the average value.

Pay attention that the maximum memory capacity of 30

memories is not exceeded. When the 30 memory is full,

the oldest value is automatically overwritten with the 31

value. Values should be evaluated by a doctor before the

memory capacity is reached – otherwise data will be lost.

Clearing all values

If you are sure that you want to permanently remove all stored

values, hold down the M-button (the device must have been

switched off beforehand) until «CL ALL» appears and then

release the button. To permanently clear the memory, press the

time button while «CL ALL» is flashing. Individual values cannot

be cleared.

Cancel deletion: press ON/OFF button 1 while «CL

ALL» is flashing.

5. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol

AM will flash as soon as the device is switched on (partly filled

Range Systolic Diastolic Recommendation

1. blood pressure

too high

≥135 ≥85 Seek medical

advice

2. blood pressure

elevated

130 - 134 80 - 84 Self-check

3. blood pressure

normal

<130 <80 Self-check

Information for the doctor in case of repeated appearance of

the IHB symbol:

This device is an oscillometric blood pressure monitor that also

measures the pulse during blood pressure measurement and

indicates when the heart rate is irregular.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife BPB1 Classic Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info