Bedienungsanleitung Microlife NC 150 (Seite 5 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

536862

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

3NC 150



Ready for measuring

When the unit is ready for measuring,

the «

°C

» or «

°F

» icon will keep flashing while the mode icon

(body or object) will be displayed.

 Measurement complete AL: The reading will be shown on the

display 3 with the «°C» or «°F» icon and the mode icon

steady. The unit is ready for the next measurement as soon as

the «°C» or «°F» icon is flashing again.

 Low battery indicator AO: When the unit is turned on, the «»

icon will keep flashing to remind the user to replace the battery.

5. Setting Date, Time and Beeper Functions

Setting the date and time

1. After the new batteries are fitted, the year number flashes in the

display BP. You can set the year by pressing the START button

4. To confirm and then set the month, press the M-button 8.

2. Press the START button 4 to set the month. Press the M-

button 8 to confirm and then set the day.

3. Follow the instructions above to set the day, 12 or 24 hour

mode, hours and minutes.

4. Once you have set the minutes and pressed the M-button 8,

the date and time are set and the time is displayed.



If no button is pressed for 20 seconds, the device automat-

ically switches to ready for measuring AK.



Cancel time setup: Press the ON/OFF button 5 during

time setup. The LCD will show Date/Time icons with «--:--».

After that press the ON/OFF button 5 to start the measure-

ment. If no further action is taken within 20 seconds, the

device will automatically turn off.



Change current date and time: Press and hold the M-

button 8 for approx. 3 seconds until the year number

starts to flash BP. Now you can enter the new values as

described above.

Setting the beeper

1. When the device is switched off, press and hold the ON/OFF

button 5 for 5 seconds to set the beeper BQ.

2. Press the ON/OFF button 5 again to either turn the beeper on

or off. The beeper is activated when the beeper icon BQ is not

crossed-out.



If no button is pressed for 5 seconds, the device automati-

cally switches to ready for measuring AK.

6. Changing between Body and Object Mode

For changing from body to object mode, slide the mode switch 6

at the side of the thermometer downwards. For switching back to

body mode, slide the switch up again.

7. Directions for Use

Measuring in body mode

1. Press the ON/OFF button 5. The display 3 is activated to

show all segments for 1 second.

2. When the «°C» or «°F» icon is flashing, a beep sound is heard

and the thermometer is ready for measuring AK.

3. Aim the thermometer at the center of the forehead with a

distance of no more than 5 cm. Please remove any hair,

sweat or dirt from the forehead before measuring to improve the

accuracy of the readings.

4. Press the START button 4 and steadily move the ther-

mometer from the middle of the forehead to the temple area

(about 1 cm above the eyebrow). The activated blue tracking

light will indicate the area being measured. After 3 seconds a

long beep will verify the completion of measurement. If the

temple area hasn’t been reached before the long beep is heard,

repeat the measurement as described above, but move the

thermometer a little faster.

5. Read the recorded temperature from the LCD display.

Measuring in object mode

1. Follow steps 1-2 above, then aim the thermometer at the center

of the object you want to measure with a distance of no more

than 5 cm. Press the START button 4. After 3 seconds a long

beep will verify the completion of measurement.

2. Read the recorded temperature from the LCD display.



NOTE:

 Patients and thermometer should stay in similar room

condition for at least 30 minutes.

 Don't take a measurement while or immediately after nursing a

baby.

 Don't use the thermometer in high humidity environments.

 Patients should not drink, eat or exercise before/while taking

the measurement.

 Don't move the measurement device from the measuring area

before hearing the termination beep.

 10 short beeps and a red LCD backlight alerts the patient that

he/she may have a temperature equal to or higher than 37.5 °C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife NC 150 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info